Surface tension is a physical property of liquids that arises from the cohesive forces
between liquid molecules at the liquid-vapor interface. The molecules inside the liquid
experience balanced intermolecular forces from all directions. However, the molecules at the
surface experience a net inward force because they lack neighboring molecules on one side.
This imbalance creates a tendency for the liquid surface to minimize its surface area.
Surface tension acts like an invisible thin elastic membrane that forms on the surface.
Surface tension represents the force per unit length acting along the surface of a fluid.
It plays a critical role at the interfaces between liquids and deformable structures for
various scientific, industrial, and medical applications. Practical examples include
electronic chip manufacturing (for example, surface tension-driven self-assembly during
solder reflow), glass forming, and capillary action. In finite element simulations, surface
tension can be modeled as a distributed membrane tension force acting tangentially on the
exterior surface of the material. In Abaqus/Explicit, it can be applied as surface-based distributed loads with load type label
ST.
Specifying Surface Tension Loads
Surface tension is an inherent property of the liquid-gas (or liquid-vapor) interface.
Therefore, its value depends on the surrounding environment (which usually is not modeled
with finite elements).
The effect of surface tension in mechanical systems becomes more significant when the
material is a fluid or a soft solid (for example, gel, molten glass, etc.). Surface tension
leads to a pressure difference, , between the fluid pressure, and the environment pressure, , which is described by the Young-Laplace equation:
where is the surface tension of the liquid-gas interface (dimensions of force
per unit length or energy per unit area), is the surface gradient, and is the vector normal to the surface. The term represents twice the local mean curvature of the interface.
You can specify surface tension loads on the following:
any solid (continuum) stress/displacement element that supports a three-dimensional
stress state (except the incompatible mode element
C3D8I),
plane strain and axisymmetric elements,
membrane elements, and
general surface elements.
Usually, membrane and surface elements are used only as a skin on the exterior surface
of solid elements (although doing so is not required to apply surface tension loads on solid
elements).
Surface tension loads are used primarily to model the effects of surface tension on soft or
fluid-like materials. Fluid-like materials typically behave as incompressible or nearly
incompressible; therefore, selecting appropriate elements is crucial to applying surface
tension loads accurately. Adhere to the following guidelines:
Some traditional Lagrangian elements (such as full integration elements, prism
elements, triangular elements and tetrahedral elements) are not well suited for modeling
surface tension due to volumetric locking. These elements often produce overly stiff
behavior, which distorts the surface tension effects and prevents accurate force
balancing at interfaces. Therefore, you should avoid these elements for surface tension
applications and use them only for mesh transitions when necessary or as filler elements
in noncritical areas.
For general three-dimensional applications, you should use
C3D8R elements.
You can apply the surface tension loads to a surface. The surface that contains the element
and face information is defined as described in Element-Based Surface Definition
. You must
specify the surface name with load type label
ST.
Input File Usage
Use the following option to define a surface tension load:
The surface tension is ignored if it is specified directly as a surface property.
Abaqus/CAE Usage
Surface tension loads are not supported in Abaqus/CAE.
Specifying Temperature-Dependent and Field Variable–Dependent Surface Tension
Coefficients
If the surface tension coefficient is a function of temperature and predefined field
variables, you must specify the surface tension data under a surface property definition
and assign the name of the surface property to the corresponding surface definition. When
you apply surface tension loads on this surface, Abaqus automatically uses the surface tension property defined for the surface.
You can use this method even when the surface tension coefficient is a constant (that is,
not a function of temperature or predefined field variables).
Input File Usage
Use both of the following options to define a temperature- and field
variable–dependent surface tension coefficient:
Defining surface tension by using a surface property is not supported in Abaqus/CAE.
Specifying the Contact Angle
The contact angle is the equilibrium angle formed between the liquid-solid interface and
the liquid-vapor interface due to intermolecular forces. The contact angle is a measure of
the surface’s wettability, describing the tendency of the liquid to spread or bead up. A
small contact angle indicates good wettability (hydrophobic); a large contact angle (more
than ) indicates poor wettability (hydrophobic). A given system of solid,
liquid, and vapor at a given temperature and pressure has a unique equilibrium contact
angle (see Figure 1).Figure 1. Unique equilibrium contact angle.
Young’s equation describes the balance of forces at the point where a liquid droplet
meets a solid surface in a vapor:
where is the contact angle, is the solid-liquid interfacial tension, is the solid-vapor surface tension, and is the liquid-vapor surface tension.
In typical structural engineering applications, surface tension effects play a
significant role on the liquid-vapor and liquid-solid interfaces; usually they can be
ignored on the free surfaces of stiff solid components. Using Young’s equations, the
equilibrium configuration of the system can be achieved by applying a surface tension, , to the free surface of the liquid (exposed to vapor) and a surface
tension of to the surface of the liquid in contact with the solid. This approach
requires using free-slip conditions for the interaction between the fluid and the solid
(that is, free-slip wall conditions); otherwise, the equilibrium contact angle might not
be established properly.
If contact conditions are known a priori, you can directly specify different surface
tension values on the free and contacting surfaces of the liquid.
Input File Usage
Use both of the following options to define the contact angle:
Defining the surface tension contact angle is not supported in Abaqus/CAE.
Assigning a Named Surface Interaction
You must assign a named surface interaction to the contact property for individual
surfaces that are used in surface tension loads. The contact angle defined in conjunction
with the surface interaction is ignored if it is not assigned to the contact properties.
Input File Usage
Use the following options to assign a named surface interaction to the contact
property:
Example: Modeling the Interaction Directly with Boundary Conditions
This example shows a liquid-solid interaction modeled directly with boundary conditions
equivalent to the no-separation, free-slip condition (see Figure 2).
Figure 2. Interaction modeled with boundary conditions.
Alternatively, you can define the contact angle as part of the surface interaction
definition and use the general contact algorithm with the no-separation, free-slip
condition to determine the value of the surface tension applied to individual element
surfaces based on current contact conditions automatically. In this case Abaqus automatically adjusts the magnitude of the surface tension based on the evolving
contact status (see Figure 3).
Figure 3. Interaction modeled with no separation, free-slip contact.
Example: Defining the Contact Angle as a Surface Interaction Property
In this example, the contact angle is defined as a surface interaction property. The same
contact angle value is defined for all possible contact interactions between the liquid
surface and all other surfaces (see Figure 4).
Figure 4. Defining the contact angle as a surface interaction property.
Example: Defining the Contact Angles Using Different Surface Interaction Property
Definitions
In this example, pairwise specification of contact angles is defined by using different
surface interaction property definitions. The contact angle depends on whether the liquid
is in contact with solid material 1 or solid material 2 (see Figure 5).
Figure 5. Defining contact angles as the different surface interaction properties.
Contact can be established at any time during the analysis. Abaqus automatically adjusts the magnitude of the surface tension based on the evolving
contact status (see Figure 6).
Figure 6. Surface tension affected by contact.
References
Weatherburn, C.E., Differential Geometry of Three Dimensions, Cambridge University, 1955.
Saksono, P.H., , and D. Perić, , and , “On Finite Element Modelling of Surface Tension: Variational Formulation and Applications – Part I: Quasistatic Problems,” Computational Mechanics, vol. 38265, 2006.