Classical metal plasticity model with Barlat yield surfaces.
Problem description
This verification test contains a set of single-element models subject to uniaxial
tension for various off-axis angles between the material directions and the loading
direction. The test is designed to verify the yield stress ratios and strain ratios
(Lankford's r-values) obtained in the simulations against
the analytical solutions.
Model
Figure 1
shows the elements used in the analysis. All elements are subject to
uniaxial tensile loading in the global
x-direction. Each element has a unique
material orientation. In the tests using
C3D8R elements, the
material orientation is assigned such that for the three rows of
elements (from bottom to top), the loading direction lies in the
material 1-2 plane, 2-3 plane, 3-1 plane, respectively; and for the
seven columns of elements (from left to right), the off-axis angle of
loading is 0°, 15°, 30°, 45°, 60°, 75°, and 90°, respectively. In the
tests using CPS4R
elements, the material orientation is assigned such that same off-axis
angles of loading are tested.
Material
Elastic
Young's modulus,
Poisson's ratio,
Plastic
Hardening:
Yield stress
Plastic strain
150.
0.000
265.
0.247
(The units are not important.)
Four materials with Barlat anisotropy coefficients are
tested. Coefficients of the Barlat Yld2004-18p yield
surface for material 2090-T3 and 6111-T4 are shown in
Table 1.
The yield surfaces of the material 2090-T3 predicted by
the Barlat Yld2004-18p model are illustrated in Figure 2,
Figure 3,
and Figure 4
for three possible plane stress conditions,
respectively. Material 2090-T3 is also modeled with
Barlat Yld2000-2d yield surfaces, and the coefficients
are listed in Table 3. The yield surface of the material 2090-T3 predicted
by the Barlat Yld2000-2d model is shown in Figure 8. The other two materials, 2024-T3 and 2008-T4, use
the Barlat Yld91 yield surface with anisotropy
coefficients as shown in Table 2.
In addition, the Mises isotropic plasticity is recovered
with an equivalent definition for the Barlat yield
surfaces.
Results and discussion
The yield stress ratio is defined as
where is the stress in the loading direction that can be obtained as
output variable S11 in the global
frame and is the reference yield stress that can be obtained as output
variable YIELDPOT.
The strain ratio (Lankford's r-value) is defined as
where and are the plastic strains in the width and thickness directions,
respectively, corresponding to output variables
PE22 and
PE33 in the global frame.
The results of the yield stress and strain ratios agree well with the analytical
solutions for the four materials. Comparisons of the simulation results using the
Barlat Yld2004-18p model and analytical solutions for the material 2090-T3 with
loading applied on three material planes are shown in Figure 5,
Figure 6,
and Figure 7.
Figure 9
compares the plastic strains of material 2090-T3 at different off-axis loading
angles in the 1-2 plane. The predictions given by the Barlat Yld2004-18p model and
the Barlat Yld2000-2d model match very well.
The yield stress ratio and strain ratio of the Mises plasticity are always one. The
models with equivalent definitions of the Mises yield surface also match the
analytical solutions.
Analysis using CPS4R
elements and the Barlat Yld91 yield surface with an equivalent
definition of the Mises yield surface.
References
Barlat, F., H. Aretz, J. W. Yoon, M. E. Karabin, J. C. Brem, and R. E. Dick, “Linear
Transformation-based Anisotropic Yield Functions,” International Journal of
Plasticity, vol. 21, pp. 1009–1039, 2005.
Barlat, F., D. J. Lege, and J. C. Brem, “A Six-Component
Yield Function for Anisotropic Materials,” International Journal of
Plasticity, vol. 7, pp. 693–712, 1991.
Barlat, F., J. C. Brem, J. W. Yoon, K. Chung, R. E. Dick, D. J. Lege, F. Pourboghrat, S. H. Choi, and E. Chu, “Plane Stress Yield Function for Aluminum Alloy Sheets—Part 1: Theory,” International Journal of Plasticity, vol. 19, pp. 1297–1319, 2003.
Tables
Table 1. Anisotropic coefficients of the Barlat Yld2004-18p yield surface for material
6111-T4 and 2090-T3 (Barlat et. al, 2005).
Abaqus notation
Barlat's notation
Material 2090-T3
Material 6111-T4
8.0
8.0
-0.069888
1.078271
0.936408
1.078271
0.079143
1.216463
1.003060
1.223867
0.524741
1.093105
1.363180
0.889161
0.477161
0.674547
0.534530
0.278587
0.511885
0.250955
0.981171
0.775366
0.476741
0.922743
0.575316
0.765487
0.866827
0.793356
1.145010
0.918689
-0.079294
1.027625
0.702310
0.294894
0.573550
0.556137
0.525830
0.557917
Table 2. Anisotropic coefficients of the Barlat Yld91 yield surface for material
2008-T4 and 2024-T3 (Barlat et. al, 1991).
Coefficients
Material 2024-T3
Material 2008-T4
8.0
11.0
1.378
1.222
1.044
1.013
0.955
0.985
1.0
1.0
1.0
1.0
1.210
1.0
Table 3. Anisotropic coefficients of the Barlat Yld2000-2d yield surface for material
2090-T3 (Barlat et. al, 2003).
Coefficients
Material 2090-T3
8
0.4865
1.378
0.7536
1.0246
1.0363
0.9036
1.2321
1.4858
Figures
Figure 1. Elements and their material orientations. Figure 2. Yield surface of material 2090-T3 with an assumption of plane stress in the
material 1–2 plane. Figure 3. Yield surface of material 2090-T3 with an assumption of plane stress in the
material 2–3 plane. Figure 4. Yield surface of material 2090-T3 with an assumption of plane stress in the
material 3–1 plane. Figure 5. Yield stress ratios and strain ratios (r-values) of off-axis uniaxial loading
in the material 1–2 plane for material 2090-T3. Figure 6. Yield stress ratios and strain ratios (r-values) of off-axis uniaxial loading
in the material 2–3 plane for material 2090-T3. Figure 7. Yield stress ratios and strain ratios (r-values) of off-axis uniaxial loading
in the material 3–1 plane for material 2090-T3. Figure 8. Yield surface of material 2090-T3 predicted with the Barlat Yld2000-2d
model. Figure 9. Comparisons of the plastic strains predicted by Barlat Yld2004-18p and
Barlat Yld2000-2d models.