*ELASTIC

Products Abaqus/Standard Abaqus/Explicit Abaqus/CAE

Type Model data

LevelModel

Abaqus/CAE Property module

Optional parameters

COHESIVE OFFSET

This parameter is relevant only for pore pressure, coupled temperature-pore pressure, and coupled slurry-temperature-pore pressure cohesive elements in Abaqus/Standard. It must be used in conjunction with either TYPE=COUPLED TRACTION or TYPE=TRACTION.

Set COHESIVE OFFSET=USER to define cohesive offset in user subroutine UCOHESIVEOFFSET.

COMPRESSION FACTOR

This parameter is meaningful only for uncoupled traction-separation elastic behavior.

Set this parameter equal to the factor by which the elastic modulus, $E_{n n}$ , must be scaled in compression. The use of a factor that is different from 1.0 results in different elastic moduli in tension and compression.

DEPENDENCIES

Set this parameter equal to the number of field variable dependencies included in the definition of the moduli. If this parameter is omitted, it is assumed that the moduli are constant or depend only on temperature. See Material Data Definition for more information.

This parameter is not relevant in an Abaqus/Standard analysis if spatially varying elastic moduli are defined using a distribution. See Distribution Definition.

MODULI

This parameter is applicable only when the ELASTIC option is used in conjunction with the VISCOELASTIC option.

Set MODULI=INSTANTANEOUS to indicate that the elastic material constants define the instantaneous behavior. This parameter value is not available for frequency domain viscoelasticity in an Abaqus/Standard analysis.

Set MODULI=LONG TERM (default) to indicate that the elastic material constants define the long-term behavior.

TYPE

Set TYPE=ANISOTROPIC to define fully anisotropic behavior.

Set TYPE=BILAMINA to define an orthotropic material with a different Young's modulus and Poisson's ratio in tension and compression in plane stress. This parameter setting is applicable only in Abaqus/Explicit.

Set TYPE=COUPLED TRACTION to define coupled traction behavior for cohesive elements.

Set TYPE=ENGINEERING CONSTANTS to define orthotropic behavior by giving the “engineering constants” (the generalized Young's moduli, the Poisson's ratios, and the shear moduli in the principal directions).

Set TYPE=ISOTROPIC (default) to define isotropic behavior.

Set TYPE=LAMINA to define an orthotropic material in plane stress.

Set TYPE=ORTHOTROPIC to define orthotropic behavior by giving the elastic stiffness matrix directly.

Set TYPE=SHEAR to define the (isotropic) shear elastic modulus. This parameter setting is applicable only in conjunction with the EOS option in Abaqus/Explicit.

Set TYPE=SHORT FIBER to define laminate material properties for each layer in each shell element. This parameter setting is applicable only when using Abaqus/Standard in conjunction with the abaqus moldflow execution procedure. Any data lines given will be ignored. Material properties will be read from the ASCII neutral file identified as jobid.shf. See Translating Moldflow Data to Abaqus Input Files for more information.

Set TYPE=TRACTION to define orthotropic shear behavior for 1-DOF warping elements or uncoupled traction behavior for cohesive elements.

Set TYPE=TRANSVERSELY ISOTROPIC to define transversely isotropic behavior by giving the five “engineering constants” (the generalized Young's moduli, the Poisson's ratios, and the shear moduli in the principal directions).

When using a distribution to define elastic moduli, the TYPE parameter must be used to indicate the level of anisotropy in the elastic behavior. The level of anisotropy must be consistent with that defined in the distribution. See Distribution Definition.

Data lines to define fully anisotropic elasticity directly (TYPE=ANISOTROPIC)

First line

$D_{1111}$ . (Units of FL⁻².)
$D_{1122}$ .
$D_{2222}$ .
$D_{1133}$ .
$D_{2233}$ .
$D_{3333}$ .
$D_{1112}$ .
$D_{2212}$ .

Second line

$D_{3312}$ .
$D_{1212}$ .
$D_{1113}$ .
$D_{2213}$ .
$D_{3313}$ .
$D_{1213}$ .
$D_{1313}$ .
$D_{1123}$ .

Third line

$D_{2223}$ .
$D_{3323}$ .
$D_{1223}$ .
$D_{1323}$ .
$D_{2323}$ .
Temperature.
First field variable.
Second field variable.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than two)

Third field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic behavior as a function of temperature and other predefined field variables.

Data lines to define bilamina elasticity (TYPE=BILAMINA)

First line

$E_{1 +}$ .
$E_{2 +}$ .
$v_{12 +}$ .
$G_{12}$ .
$E_{1 -}$ .
$E_{2 -}$ .
$v_{12 -}$ .
Temperature.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than or equal to one)

First field variable.
Second field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic behavior as a function of temperature and other predefined field variables.

Data lines to define coupled traction separation behavior for cohesive elements (TYPE=COUPLED TRACTION)

First line

$E_{n n}$ .
$E_{s s}$ .
$E_{t t}$ .
$E_{n s}$ .
$E_{n t}$ .
$E_{s t}$ .
Temperature.
First field variable.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than one)

Second field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic behavior as a function of temperature and other predefined field variables.

Data lines to define orthotropic elasticity with moduli (TYPE=ENGINEERING CONSTANTS)

First line

$E_{1}$ .
$E_{2}$ .
$E_{3}$ .
$ν_{12}$ .
$ν_{13}$ .
$ν_{23}$ .
$G_{12}$ .
$G_{13}$ .

Second line

$G_{23}$ .
Temperature, $θ$ .
First field variable.
Second field variable.
Etc., up to six field variables.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than six)

Seventh field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic behavior as a function of temperature and other predefined field variables.

Data lines to define isotropic elasticity (TYPE=ISOTROPIC)

First line

Young's modulus, E.
Poisson's ratio, $ν$ .
Temperature, $θ$ .
First field variable.
Second field variable.
Etc., up to five field variables.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than five)

Sixth field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic behavior as a function of temperature and other predefined field variables.

Data lines to define orthotropic elasticity in plane stress (TYPE=LAMINA)

First line

$E_{1}$ .
$E_{2}$ .
$ν_{12}$ .
$G_{12}$ .
$G_{13}$ . This shear modulus is needed to define transverse shear behavior in shells.
$G_{23}$ . This shear modulus is needed to define transverse shear behavior in shells.
Temperature.
First field variable.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than one)

Second field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic behavior as a function of temperature and other predefined field variables.

Data lines to define orthotropic elasticity directly (TYPE=ORTHOTROPIC)

First line

$D_{1111}$ . (Units of FL⁻².)
$D_{1122}$ .
$D_{2222}$ .
$D_{1133}$ .
$D_{2233}$ .
$D_{3333}$ .
$D_{1212}$ .
$D_{1313}$ .

Second line

$D_{2323}$ .
Temperature.
First field variable.
Second field variable.
Etc., up to six field variables.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than six)

Seventh field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic behavior as a function of temperature and other predefined field variables.

Data lines to define isotropic elastic shear behavior (TYPE=SHEAR)

First line

Shear modulus, G. (Units of FL⁻².)
Temperature.
First field variable.
Second field variable.
Etc., up to six field variables.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than six)

Seventh field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic shear modulus as a function of temperature and other predefined field variables.

Data lines to define orthotropic shear behavior for 1-DOF warping elements or uncoupled traction behavior for cohesive elements (TYPE=TRACTION)

First line (only line for defining orthotropic shear behavior for 1-DOF warping elements; in this case the data cannot be defined as functions of temperature and/or field variables)

E for 1-DOF warping elements; $E_{n n}$ for cohesive elements.
$G_{1}$ for 1-DOF warping elements; $E_{s s}$ for cohesive elements.
$G_{2}$ for 1-DOF warping elements; $E_{t t}$ for cohesive elements.
Temperature.
First field variable.
Etc., up to four field variables per line.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than four; relevant only for defining uncoupled traction behavior of cohesive elements)

Fifth field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic behavior as a function of temperature and other predefined field variables.

Data lines to define transversely isotropic elasticity with moduli (TYPE=TRANSVERSELY ISOTROPIC)

First line

$E_{1}$ .
$E_{2}$ .
$ν_{12}$ .
$ν_{23}$ .
$G_{12}$ .
Temperature, $θ$ .
First field variable.
Second field variable.

Subsequent lines (only needed if the DEPENDENCIES parameter has a value greater than two)

Third field variable.
Etc., up to eight field variables per line.

Repeat this set of data lines as often as necessary to define the elastic behavior as a function of temperature and other predefined field variables.

Data line to define spatially varying elastic behavior for solid continuum elements in an Abaqus/Standard analysis using a distribution. (Distributions are supported for TYPE=ISOTROPIC, TYPE=ENGINEERING CONSTANTS, TYPE=LAMINA, TYPE=ORTHOTROPIC, and TYPE=ANISOTROPIC)

First line

Distribution name. The data defined in the distribution must be in units that are consistent with the prescribed TYPE.