Defining the Constitutive Response of Fluid within the Cohesive Element Gap

The cohesive element fluid flow model:

is typically used in geotechnical applications, where fluid flow continuity within the gap and through the interface must be maintained;
enables fluid pressure on the cohesive element surface to contribute to its mechanical behavior, which enables the modeling of hydraulically driven fracture;
enables modeling of an additional resistance layer on the surface of the cohesive element; and
can be used only in conjunction with traction-separation behavior.

The features described in this section are used to model fluid flow within and across surfaces of pore pressure cohesive elements.

This page discusses:

Defining Pore Fluid Flow Properties
Specifying the Fluid Flow Properties
Initially Open Elements
Use of Unsymmetric Matrix Storage and Solution
Additional Considerations
Output

Defining Pore Fluid Flow Properties

The fluid constitutive response comprises:

Tangential flow within the gap, which can be modeled with either a Newtonian or power law model; and
Normal flow across the gap, which can reflect resistance due to caking or fouling effects.

The flow patterns of the pore fluid in the element are shown in Figure 1.

The fluid is assumed to be incompressible, and the formulation is based on a statement of flow continuity that considers tangential and normal flow and the rate of opening of the cohesive element.

Specifying the Fluid Flow Properties

You can assign tangential and normal flow properties separately.

Tangential Flow

By default, there is no tangential flow of pore fluid within the cohesive element. To allow tangential flow, define a gap flow property in conjunction with the pore fluid material definition.

Newtonian Fluid

In the case of a Newtonian fluid the volume flow rate density vector is given by the expression

q d = - k_{t} \nabla p,

where $k_{t}$ is the tangential permeability (the resistance to the fluid flow), $\nabla p$ is the pressure gradient along the cohesive element, and $d$ is the gap opening.

In Abaqus the gap opening, $d$ , is defined as

d = t_{c u r r} - t_{o r i g} + g_{i n i t},

where $t_{c u r r}$ and $t_{o r i g}$ are the current and original cohesive element geometrical thicknesses, respectively; and $g_{i n i t}$ is the initial gap opening, which has a default value of 0.002.

Abaqus defines the tangential permeability, or the resistance to flow, according to Reynold's equation:

k_{t} = \frac{d^{3}}{12 μ},

where $μ$ is the fluid viscosity and $d$ is the gap opening. You can also specify an upper limit on the value of $k_{t}$ .

Input File Usage

Use the following option to define the initial gap opening directly:

SECTION CONTROLS, INITIAL GAP OPENING

Use the following option to define the tangential flow in a Newtonian fluid:

GAP FLOW, TYPE=NEWTONIAN, KMAX

Abaqus/CAE Usage

Initial gap opening is not supported in Abaqus/CAE.

Property module: material editor: OtherPore FluidGap Flow: Type: Newtonian: Toggle on Maximum Permeability and enter the value of  $k_{\max}$

Power Law Fluid

In the case of a power law fluid the constitutive relation is defined as

τ = K {\dot{γ}}^{α},

where $τ$ is the shear stress, $\dot{γ}$ is the shear strain rate, $K$ is the fluid consistency, and $α$ is the power law coefficient. Abaqus defines the tangential volume flow rate density as

q d = - (\frac{2 α}{1 + 2 α}) {(\frac{1}{K})}^{\frac{1}{α}} {(\frac{d}{2})}^{\frac{1 + 2 α}{α}} {∥ \nabla p ∥}^{\frac{1 - α}{α}} \nabla p,

where $d$ is the gap opening.

Input File Usage

GAP FLOW, TYPE=POWER LAW

Abaqus/CAE Usage

Property module: material editor: OtherPore FluidGap Flow: Type: Power law

Bingham Plastic Fluid

In the case of a Bingham plastic fluid the volume flow rate density vector is given by the expression

q d = - (\frac{1}{3}) (\frac{1}{K}) {(\frac{d}{2})}^{3} \nabla p {(1 - \frac{2 τ_{0}}{2 d ‖ \nabla p ‖})}^{2} (2 + \frac{2 τ_{0}}{d ‖ \nabla p ‖}),

where $K$ is the fluid consistency, $τ_{0}$ is the yield stress, and $d$ is the gap opening. The unyielded fluid is modeled as a Newtonian fluid with viscosity equal to $P_{τ} \times K$ , where $P_{τ}$ has a default value of 10⁷.

Input File Usage

GAP FLOW, TYPE=BINGHAM PLASTIC, PTAU= $P_{τ}$

Abaqus/CAE Usage

Property module: material editor: OtherPore FluidGap Flow: Type: Bingham plastic

Herschel-Bulkley Fluid

In the case of a Herschel-Bulkley fluid the volume flow rate density vector is given by the expression

q d = - 2 [(\frac{α}{1 + α}) (\frac{α}{1 + 2 α})] {(\frac{1}{K})}^{\frac{1}{α}} {(\frac{d}{2})}^{\frac{1 + 2 α}{α}} {‖ \nabla p ‖}^{\frac{1 - α}{α}} {(1 - \frac{2 τ_{0}}{d ‖ \nabla p ‖})}^{\frac{1 + α}{α}} (\frac{1}{α} + 1 + \frac{2 τ_{0}}{d ‖ \nabla p ‖}) \nabla p,

where $K$ is the fluid consistency, $α$ is the power law coefficient, $τ_{0}$ is the yield stress, and $d$ is the gap opening. The unyielded fluid is modeled as a Newtonian fluid with viscosity equal to $P_{τ} \times K$ , where $P_{τ}$ has a default value of 10⁷.

Input File Usage

GAP FLOW, TYPE=HERSCHEL-BULKLEY, PTAU= $P_{τ}$

Abaqus/CAE Usage

Property module: material editor: OtherPore FluidGap Flow: Type: Herschel-Bulkley

Normal Flow across Gap Surfaces

You can permit normal flow by defining a fluid leak-off coefficient for the pore fluid material. This coefficient defines a pressure-flow relationship between the cohesive element's middle nodes and their adjacent surface nodes. The fluid leak-off coefficients can be interpreted as the permeability of a finite layer of material on the cohesive element surfaces, as shown in Figure 2.

The normal flow is defined as

q_{t} = c_{t} (p_{i} - p_{t})

and

q_{b} = c_{b} (p_{i} - p_{b}),

where $q_{t}$ and $q_{b}$ are the flow rates into the top and bottom surfaces, respectively; $p_{i}$ is the midface pressure; and $p_{t}$ and $p_{b}$ are the pore pressures on the top and bottom surfaces, respectively.

Input File Usage

FLUID LEAKOFF

Abaqus/CAE Usage

Property module: material editor: OtherPore FluidFluid Leakoff: Type: Coefficients

Defining Leak-off Coefficients as a Function of Temperature and Field Variables

You can optionally define leak-off coefficients as functions of temperature and field variables.

Input File Usage

FLUID LEAKOFF, DEPENDENCIES

Abaqus/CAE Usage

Property module: material editor: OtherPore FluidFluid Leakoff: Type: Coefficients: Toggle on Use temperature-dependent data and select the number of field variables.

Defining Leak-off Coefficients in a User Subroutine

User subroutine UFLUIDLEAKOFF can also be used to define more complex leak-off behavior, including the ability to define a time accumulated resistance, or fouling, through the use of solution-dependent state variables.

Input File Usage

FLUID LEAKOFF, USER

Abaqus/CAE Usage

Property module: material editor: OtherPore FluidFluid Leakoff: Type: User

Tangential and Normal Flow Combinations

Table 1 shows the permitted combinations of tangential and normal flow and the effects of each combination.

Table 1. Effects of flow property definition combinations.
	Normal flow is defined	Normal flow is undefined
Tangential flow is defined	Tangential and normal flow are modeled.	Tangential flow is modeled. Pore pressure continuity is enforced between facing nodes in the cohesive element only when the element is closed. Otherwise, the surfaces are impermeable in the normal direction.
Tangential flow is undefined	Normal flow is modeled.	Tangential flow is not modeled. Pore pressure continuity is always enforced between facing nodes in the cohesive element.

Initially Open Elements

When the opening of the cohesive element is driven primarily by entry of fluid into the gap, you will have to define one or more elements as initially open, since tangential flow is possible only in an open element. Identify initially open elements as initial conditions.

Input File Usage

INITIAL CONDITIONS, TYPE=INITIAL GAP

Abaqus/CAE Usage

Initial gap definition is not supported in Abaqus/CAE.

Use of Unsymmetric Matrix Storage and Solution

The pore pressure cohesive element matrices are unsymmetric; therefore, unsymmetric matrix storage and solution may be needed to improve convergence (see Matrix Storage and Solution Scheme in Abaqus/Standard).

Additional Considerations

Your use of cohesive element fluid properties and your property values can impact your solution in some cases.

Large Coefficient Values

You must make sure that the tangential permeability or fluid leak-off coefficients are not excessively large. If either coefficient is many orders of magnitude higher than the permeability in the adjacent continuum elements, matrix conditioning problems may occur, leading to solver singularities and unreliable results.

Use in Total Pore Pressure Simulations

Definition of tangential flow properties may result in inaccurate results if the total pore pressure formulation is used and the hydrostatic pressure gradient contributes significantly to the tangential flow in the gap. The total pore pressure formulation is invoked if you apply gravity distributed loads to all elements in the model. The results will be accurate if the hydrostatic pressure gradient (i.e., the gravity vector) is perpendicular to the cohesive element.

Output

The following output variables are available when flow is enabled in pore pressure cohesive elements:

GFVR: Gap fluid volume rate.
PFOPEN: Fracture opening.
LEAKVRT: Leak-off flow rate at element top.
ALEAKVRT: Accumulated leak-off flow volume at element top.
LEAKVRB: Leak-off flow rate at element bottom.
ALEAKVRB: Accumulated leak-off flow volume at element bottom.
FLDVEL: Material point fluid velocity.