The output variables listed below are available in Abaqus/Standard.
Adaptive Mesh Domains
The following variable is available only for adaptive domains (see Defining ALE Adaptive Mesh Domains in Abaqus/Standard).
-
VOLC
- Field: no History: yes .fil: yes .dat: yes
Change in area or change in volume of an element set solely due to adaptive meshing.
Equivalent Rigid Body Motion Variables
You can request equivalent rigid body motion whole element set variable output to the
data, results, or output database file (see Element Output and Writing Element Output to the Output Database). The variables listed are available only for implicit dynamic analyses
using direct integration except where indicated.
-
XC
- Field: no History: yes .fil: yes .dat: yes
Current coordinates of the center of mass for the entire set or the entire model. Not
available for eigenfrequency extraction, eigenvalue buckling prediction, complex
eigenfrequency extraction, or linear dynamics procedures. Available also for static
analyses but only from the output database.
-
XCn
- Field: no History: yes .fil: no .dat: yes
Coordinate n of the center of mass for the entire set or
the entire model (
).
-
UC
- Field: no History: yes .fil: yes .dat: yes
Current displacement of the center of mass for the entire set or the entire model.
Available also for static analyses but only from the output database.
-
UCn
- Field: no History: yes .fil: no .dat: yes
Displacement component n of the center of mass for the
entire set or the entire model (
).
-
URCn
- Field: no History: yes .fil: no .dat: yes
Rotation component n of the center of mass for the entire
set or the entire model (
).
-
VC
- Field: no History: yes .fil: yes .dat: yes
Equivalent rigid body velocity components summed over the entire set or the entire
model.
-
VCn
- Field: no History: yes .fil: no .dat: yes
Component n of the equivalent rigid body velocity summed
over the entire set or the entire model (
).
-
VRCn
- Field: no History: yes .fil: no .dat: yes
Component n of the equivalent rigid body angular velocity
summed over the entire set or the entire model (
).
-
HC
- Field: no History: yes .fil: yes .dat: yes
Current angular momentum about the center of mass for the entire set or the entire
model.
-
HCn
- Field: no History: yes .fil: no .dat: yes
Component n of the angular momentum about the center of
mass for the entire set or the entire model (
).
-
HO
- Field: no History: yes .fil: yes .dat: yes
Current angular momentum about the origin for the entire set or the entire model.
-
HOn
- Field: no History: yes .fil: no .dat: yes
Component n of the angular momentum about the origin for
the entire set or the entire model (
).
-
RI
- Field: no History: yes .fil: yes .dat: yes
Current rotary inertia about the origin of the entire set or the entire model. Not
available for eigenfrequency extraction, eigenvalue buckling prediction, complex
eigenfrequency extraction, or linear dynamics procedures. Available also for static
analyses but only from the output database.
-
RIij
- Field: no History: yes .fil: no .dat: yes
-component of the rotary inertia about the origin of the entire set
or the entire model (
).
-
MASS
- Field: no History: yes .fil: yes .dat: yes
Current mass of the entire set or the entire model. Available also for static
analyses but only from the output database.
-
VOL
- Field: no History: yes .fil: yes .dat: yes
Current volume of the entire set or the entire model. Available also for static
analyses but only from the output database. (Available only for continuum and
structural elements that do not use general beam or shell section definitions.)
Inertia Relief Output Variables
You can request inertia relief whole model variable output to the data or output
database file (see Element Output
and Writing Element Output to the Output Database). Since these variables have unique values for the entire
model, the variable output is independent of the specified region. The variables listed are
available only for those analyses that include inertia relief loading (see Inertia Relief).
-
IRX
- Field: no History: yes .fil: no .dat: yes
Current coordinates of the reference point.
-
IRXn
- Field: no History: yes .fil: no .dat: yes
Coordinate n of the reference point (
).
-
IRA
- Field: no History: yes .fil: no .dat: yes
Equivalent rigid body acceleration components.
-
IRAn
- Field: no History: yes .fil: no .dat: yes
Component n of the equivalent rigid body acceleration (
).
-
IRARn
- Field: no History: yes .fil: no .dat: yes
Component n of the equivalent rigid body angular
acceleration with respect to the reference point (
).
-
IRF
- Field: no History: yes .fil: no .dat: yes
Inertia relief load corresponding to the equivalent rigid body acceleration.
-
IRFn
- Field: no History: yes .fil: no .dat: yes
Component n of the inertia relief load corresponding to
the equivalent rigid body acceleration (
).
-
IRMn
- Field: no History: yes .fil: no .dat: yes
Component n of the inertia relief moment corresponding to
the equivalent rigid body angular acceleration with respect to the reference point (
).
-
IRRI
- Field: no History: yes .fil: no .dat: yes
Rotary inertia about the reference point.
-
IRRIij
- Field: no History: yes .fil: no .dat: yes
-component of the rotary inertia about the reference point (
).
-
IRMASS
- Field: no History: yes .fil: no .dat: yes
Whole model mass.
Mass Diffusion Analysis
You can request variable output from a mass diffusion analysis (Mass Diffusion Analysis) to the data,
results, or output database file (see Element Output and Writing Element Output to the Output Database). If you specify an output region, the variable is calculated over the
user-specified region. If you do not specify an output region, the variable is calculated as
the total over the entire model.
-
SOL
- Field: no History: yes .fil: yes .dat: yes
Amount of solute in an element set, calculated as the sum of
ESOL (amount of solute in each
element) over all the elements in the set.
Analyses with Time-Dependent Material Behavior
-
CRPTIME
- Field: no History: yes .fil: no .dat: no
Creep time, which is equal to the total time in procedures with time-dependent
material behavior (see Rate-Dependent Plasticity: Creep and Swelling).
Total Energy Output Quantities
If the following whole model variables are relevant for a particular analysis, you can
request them as output to the data, results, or output database file (see Total Energy Output and Total Energy Output). If you do not specify an output region, whole model variables are calculated. When you
specify an output region, the relevant energy totals are calculated over the user-specified
region.
These variables are not available for eigenvalue buckling prediction, eigenfrequency
extraction, or complex frequency extraction analysis. You cannot specify an output region
for modal dynamic, random response, response spectrum, or steady-state dynamic
analysis.
See Energy balance and Energy computations in a contact analysis for details of
the energy definitions. In steady-state dynamics all energy quantities are net per-cycle
values, unless otherwise noted.
-
ALLAE
- Field: no History: yes .fil: automatic .dat: automatic
“Artificial” strain energy associated with constraints used to remove singular modes
(such as hourglass control), and with constraints used to make the drill rotation
follow the in-plane rotation of the shell elements.
-
ALLCCDW
- Field: no History: yes .fil: no .dat: automatic
Contact constraint discontinuity work.
-
ALLCCEN
- Field: no History: yes .fil: no .dat: automatic
Contact constraint elastic energy in normal direction due to penalty constraint
enforcement.
-
ALLCCET
- Field: no History: yes .fil: no .dat: automatic
Contact constraint elastic energy in tangential direction due to friction penalty
constraint enforcement.
-
ALLCCE
- Field: no History: yes .fil: no .dat: automatic
The sum of ALLCCEN and
ALLCCET.
-
ALLCCSDN
- Field: no History: yes .fil: no .dat: automatic
Contact constraint stabilization dissipation in normal direction.
-
ALLCCSDT
- Field: no History: yes .fil: no .dat: automatic
Contact constraint stabilization dissipation in tangential direction.
-
ALLCCSD
- Field: no History: yes .fil: no .dat: automatic
The sum of ALLCCSDN and
ALLCCSDT.
-
ALLCD
- Field: no History: yes .fil: automatic .dat: automatic
Energy dissipated by creep, swelling, viscoelasticity, and energy associated with
viscous regularization for cohesive elements and cohesive contact.
-
ALLCDCOH
- Field: no History: yes .fil: no .dat: no
Energy associated with viscous regularization for cohesive elements and cohesive
contact.
-
ALLEE
- Field: no History: yes .fil: automatic .dat: automatic
Electrostatic energy.
-
ALLFD
- Field: no History: yes .fil: automatic .dat: automatic
Total energy dissipated through frictional effects. (Available only for the whole
model.)
-
ALLIE
- Field: no History: yes .fil: automatic .dat: automatic
Total strain energy. (ALLIE =
ALLSE +
ALLPD +
ALLCD +
ALLAE +
ALLQB +
ALLEE +
ALLDMD.)
-
ALLJD
- Field: no History: yes .fil: automatic .dat: automatic
Electrical energy dissipated due to flow of electrical current.
-
ALLKE
- Field: no History: yes .fil: automatic .dat: automatic
Kinetic energy. In steady-state dynamic and frequency extraction analyses, this is
the cyclic mean value. In frequency extraction analyses, the value of kinetic energy
is normalized. Normalization is performed for each eigenmode separately, such that the
kinetic and strain energies for the whole model add up to one.
-
ALLKEA
- Field: no History: yes .fil: no .dat: no
Kinetic energy amplitude. This variable is available only in mode-based and
direct-solution steady-state dynamic analyses.
-
ALLKEP
- Field: no History: yes .fil: no .dat: no
Kinetic energy peak value. This variable is available only in mode-based and
direct-solution steady-state dynamic analyses.
-
ALLKL
- Field: no History: yes .fil: automatic .dat: automatic
Loss of kinetic energy at impact. (Available only for the whole model.)
-
ALLPD
- Field: no History: yes .fil: automatic .dat: automatic
Energy dissipated by rate-independent and rate-dependent plastic deformation. For
superelastic materials, this variable also includes recoverable phase-transformation
energy.
-
ALLQB
- Field: no History: yes .fil: automatic .dat: automatic
Energy dissipated through quiet boundaries (infinite elements). (Available only for
the whole model.)
-
ALLSD
- Field: no History: yes .fil: automatic .dat: automatic
Energy dissipated by automatic stabilization. This includes both volumetric static
stabilization and automatic approach of contact pairs (the latter part included only
for the whole model).
-
ALLSE
- Field: no History: yes .fil: automatic .dat: automatic
Elastic strain energy. In steady-state dynamic and frequency extraction analyses,
this is the cyclic mean value. In frequency extraction analyses, the value of strain
energy is normalized. Normalization is performed for each eigenmode separately, such
that the kinetic and strain energies for the whole model add up to one.
-
ALLSEA
- Field: no History: yes .fil: no .dat: no
Recoverable strain energy amplitude. This variable is available only in mode-based
and direct-solution steady-state dynamic analyses.
-
ALLSEP
- Field: no History: yes .fil: no .dat: no
Recoverable strain energy peak value. This variable is available only in mode-based
and direct-solution steady-state dynamic analyses.
-
ALLVD
- Field: no History: yes .fil: automatic .dat: automatic
Energy dissipated by viscous effects including viscous regularization (except for
cohesive elements and cohesive contact), not inclusive of energy dissipated by
automatic stabilization and viscoelasticity. If this variable is requested for the
whole model in mode-based steady-state dynamic analyses, it includes the energy loss
due to the material, global, and modal damping. If this variable is requested for a
part of the model in mode-based steady-state dynamic analyses, the energy loss due to
the modal damping is not included. In direct-solution steady-state dynamic analyses
this variable includes the energy loss due to the material and global damping.
-
ALLVDE
- Field: no History: yes .fil: no .dat: automatic
Energy dissipated by viscous effects due to the material damping. This variable is
available only in mode-based and direct-solution steady-state dynamic analyses.
-
ALLVDG
- Field: no History: yes .fil: no .dat: automatic
Energy dissipated by viscous effects due to the global damping. This variable is
available only in mode-based and direct-solution steady-state dynamic analyses.
-
ALLVDM
- Field: no History: yes .fil: no .dat: automatic
Energy dissipated by viscous effects due to the modal damping. This variable is
available only for the whole model in the mode-based steady-state dynamic analyses.
-
ALLHD
- Field: no History: yes .fil: no .dat: automatic
Energy dissipated due to the structural damping. If this variable is requested for
the whole model in mode-based steady-state dynamic analyses, it includes energy loss
due to the material, global, and modal damping. If this variable is requested for a
part of the model in mode-based steady-state dynamic analyses, energy loss due to the
modal damping is not included. In direct-solution steady-state dynamic analyses this
variable includes the energy loss due to the material and global damping.
-
ALLHDE
- Field: no History: yes .fil: no .dat: automatic
Energy dissipated due to the material structural damping. This variable is available
only in mode-based and direct-solution steady-state dynamic analyses.
-
ALLHDG
- Field: no History: yes .fil: no .dat: automatic
Energy dissipated due to the global structural damping. This variable is available
only in mode-based and direct-solution steady-state dynamic analyses.
-
ALLHDM
- Field: no History: yes .fil: no .dat: automatic
Energy dissipated due to the modal structural damping. This variable is available
only for the whole model in mode-based steady-state dynamic analyses.
-
ALLDMD
- Field: no History: yes .fil: automatic .dat: automatic
Energy dissipated by damage.
-
ALLWK
- Field: no History: yes .fil: automatic .dat: automatic
External work. (Available only for the whole model.)
-
ETOTAL
- Field: no History: yes .fil: automatic .dat: automatic
Total energy balance (available only for the whole model).
(ETOTAL =
ALLKE +
ALLIE +
ALLVD +
ALLSD +
ALLKL +
ALLFD +
ALLJD +
ALLCCE −
ALLWK −
ALLCCDW.)
-
EFLOW
- Field: no History: yes .fil: no .dat: automatic
Energy flow from a given portion of the model through the given boundary. This
variable is available only in mode-based and direct-solution steady-state dynamic
analyses.
-
PFLOW
- Field: no History: yes .fil: no .dat: automatic
Power flow from a given portion of the model through the given boundary. This
variable is available only in mode-based and direct-solution steady-state dynamic
analyses.
-
RADEN
- Field: no History: yes .fil: no .dat: automatic
Radiated energy from/into a given acoustic cavity through the given boundary. This
variable is available only in mode-based and direct-solution steady-state dynamic
analyses.
-
RADPOW
- Field: no History: yes .fil: no .dat: automatic
Radiated power from/into a given acoustic cavity through the given boundary. This
variable is available only in mode-based and direct-solution steady-state dynamic
analyses.
-
ALLHUMDFLUX
- Field: no History: yes .fil: no .dat: automatic
All heat energy due to the nonuniform moving flux prescribed inside user subroutine
UMDFLUX. This variable is
available only in pure heat transfer analyses. (Available only for the whole model.)
-
ALLUSER
- Field: no History: yes .fil: no .dat: no
User-defined quantity that can be set only in user subroutines for pure heat transfer
analyses. Its value is set through calls to the utility routine
SETALLUSER.
-
ALLERPWR
- Field: no History: yes .fil: no .dat: no
Equivalent radiated power emitted by a panel. This variable is available only in
steady-state dynamic analyses.
Total Amount Output Quantities
The following whole model variables are relevant only for electrochemical analyses. You
can request them as history output to the output database file. If you do not specify an
output region as an element set in the element output, whole model variables are calculated.
When you specify an output region, the relevant amount totals are calculated over the
user-specified region. Amount is measured in moles. While the output variables presented
here are in terms of lithium metal, in general, you can replace lithium with another
chemical species.
-
AMOUNT
- Field: no History: yes .fil: no .dat: no
Total amount of lithium in the solid particles and the electrolyte (sum of
AMOUNTE and
AMOUNTS).
-
AMOUNTE
- Field: no History: yes .fil: no .dat: no
Amount of lithium in the electrolyte.
-
AMOUNTS
- Field: no History: yes .fil: no .dat: no
Amount of lithium in the solid particles.
Total Volume Heat Generation Power Output Quantities
The following whole model variables are relevant only for electrochemical analyses. You
can request them as history output to the output database file. If you do not specify an
output region as an element set in the element output, whole model variables are calculated.
When you specify an output region, the relevant power totals are calculated over the
user-specified region.
-
ECHEMQV1
- Field: no History: yes .fil: no .dat: no
Total volume heat generation power of Butler-Volmer electric current,
(volume integral of
ECHEMQ1).
-
ECHEMQV2
- Field: no History: yes .fil: no .dat: no
Total volume entropic heat generation power,
(volume integral of
ECHEMQ2).
-
ECHEMQV3
- Field: no History: yes .fil: no .dat: no
Total volume heat generation power of electronic electric current,
(volume integral of
ECHEMQ3).
-
ECHEMQV4
- Field: no History: yes .fil: no .dat: no
Total volume heat generation power of ionic electric current,
(volume integral of
ECHEMQ4).
-
ECHEMQV5
- Field: no History: yes .fil: no .dat: no
Total volume heat generation power of ionic diffusive flux,
(volume integral of
ECHEMQ5).
Total Volume Hydraulic Fracturing Output Quantities
The following whole model variables are relevant only for coupled pore fluid flow and
stress analyses. You can request them as history output to the output database file. If no
specific element set is defined, the variables are calculated for the entire model;
otherwise, the relevant totals are calculated over the user-specified region. In all cases,
contributions are derived solely from cohesive elements with pore pressure degree of
freedom.
-
VOLUMEFRAC
- Field: no History: yes .fil: no .dat: no
Total fluid volume contained within the fracture.
-
VOLUMELEAKBOT
- Field: no History: yes .fil: no .dat: no
Total leak-off volume from the bottom fracture surface.
-
VOLUMELEAKTOP
- Field: no History: yes .fil: no .dat: no
Total leak-off volume from the top fracture surface.
-
VOLUMESLURRY
- Field: no History: yes .fil: no .dat: no
Total slurry volume within the fracture (slurry workflows only) .
Total State of Charge
The following whole model variable is relevant only for electrochemical analyses. You
can request it as history output to the output database file. If you do not specify an
output region as an element set in the element output, the whole model variable is
calculated. When you specify an output region, the relevant state of charge total is
calculated over the user-specified region.
-
SOC
- Field: no History: yes .fil: no .dat: no
Current state of charge in the specified region of the model.
|