Products
Abaqus/Standard
Abaqus/Explicit
Type
Model data
LevelModel
Required parameters
-
NAME
-
Set this parameter equal to a label that is used to refer to the field
mapper control definition. All field mapper control names in the same
input file must be unique.
Optional parameters
-
CONFIGURATION
-
This parameter is relevant only when importing fields to define a
distribution or an initial condition.
Set
CONFIGURATION=DEFORMED
to use the deformed configuration of the source mesh for mapping. This
parameter setting is used when the model is remeshed in the second
analysis using the deformed shape from the first analysis.
Set
CONFIGURATION=REFERENCE
(default) to use the original configuration of the source mesh for
mapping.
-
MAPPER ALGORITHM
-
This parameter is relevant only when importing history-dependent fields
when the mapper integrates to convert intensive fields to extensive
fields.
Set
MAPPER ALGORITHM=SUBELEMENT
(default) to select an algorithm based on the subelements method. This
algorithm provides conservative mapping with a smooth distribution.
Set
MAPPER ALGORITHM=GLOBAL CONSERVATIVE
to select an algorithm where the results are conservative over the
entire region. This algorithm is numerically less expensive than the
subelements method, and the mapped field might show an uneven
distribution in some cases.
-
SEARCH TOLERANCE
-
Set
SEARCH TOLERANCE=RELATIVE
(default) to specify the search tolerances as relative values to
characteristic region dimensions.
Set
SEARCH TOLERANCE=ABSOLUTE
to specify absolute search tolerances.
-
TENSOR AVERAGING
-
This parameter is relevant only for mapping three-dimensional tensor
quantities. Two-dimensional tensor quantities must use
component-by-component mapping.
Set
TENSOR AVERAGING=COMPONENT
to use component-by-component mapping. This value is the default unless
you specify S,
ORIENT, or
ORITENS as the source
field on the EXTERNAL FIELD
option.
Set
TENSOR AVERAGING=EIGENVALUE
to use a mapping technique that preserves the eigenvalues of the tensor
during mapping. This value is the default if output variable
ORITENS is specified
as the source field on the EXTERNAL FIELD
option.
Set
TENSOR AVERAGING=INVARIANT
to use a mapping technique that preserves the Mises invariant of the
stress tensor during mapping. This value is the default if output
variable S is
specified as the source field on the EXTERNAL FIELD
option.
If you specify ORIENT as the source
field on the EXTERNAL FIELD
option, Abaqus uses a special averaging technique to map orientations by default.
(ORIENT is available in the
SIM database file if you defined a
material orientation in the element section definition.)
-
UNMAPPED MEMBERS TREATMENT
-
This parameter defines how to treat unmapped members (nodes or elements
where the search algorithm fails to find intersections).
Set
UNMAPPED MEMBERS TREATMENT=ERROR
(default) to issue an error message and end the simulation if members
cannot be mapped properly when importing history-dependent fields. When
importing initial conditions and distributions, no values are applied.
Unmapped members are reported as a node set or element set.
Set
UNMAPPED MEMBERS TREATMENT=NEAREST NEIGHBOR
to assign a field value based on the nearest neighbor.
Set
UNMAPPED MEMBERS TREATMENT=CONSTANT VALUE
to specify a constant value for the unmapped member.
Data lines to define mapping specifications
- First line to specify searching
tolerances
-
Search position tolerance distance
searched on the outward-normal side of a surface facet. For a
relative search tolerance, specify a factor relative to the
characteristic facet size (default is 0.5). For an absolute
search tolerance, specify the search distance (default is
0.0).
Search position tolerance distance for the cloud point
mapping algorithm in the element face normal directions. For a
relative search tolerance, specify a factor relative to the
characteristic facet size (default is 0.5). For an absolute
search tolerance, specify the search distance (default is
0.0).
Search position tolerance distance searched outside the
source elements or outside a facet in the plane of the surface.
For a relative search tolerance, specify a factor relative to
the characteristic facet size (default is 0.5). For an absolute
search tolerance, specify the search distance (default is
0.0).
- Search tolerance radius for the nearest neighbor algorithm.
For a relative search tolerance, specify a factor relative to the
characteristic facet size (default is 0.5). For an absolute search
tolerance, specify the search distance (default is 0.0).
- Second line (optional, to be used to specify default values at
unmapped member locations where search fails)
-
Value assigned to the first component of the scalar,
vector, or tensor field at an unmapped member location.
Value assigned to the second component of the vector or
tensor field at an unmapped member location.
Value assigned to the third component of the vector or
tensor field at an unmapped member location.
Value assigned to the fourth component of the tensor field
at an unmapped member location.
Value assigned to the fifth component of the tensor field
at an unmapped member location.
Value assigned to the sixth component of the tensor field
at an unmapped member location.