Products
Abaqus/Standard
Abaqus/Explicit
Abaqus/CAE
Type
History data
LevelStep
Abaqus/CAE
Load module
Required parameter for reading concentrated nodal flux from an output database
file
-
FILE
-
Set this parameter equal to the name of the output database file from which the data
are to be read. The file extension is optional.
If this parameter is used, both the amplitude definition and the reference magnitude
are ignored.
Optional parameters
-
AMPLITUDE
-
Set this parameter equal to the name of the amplitude curve that defines the
magnitude of the flux during the step (Amplitude Curves).
If this parameter is omitted in an Abaqus/Standard analysis, the reference magnitude is applied immediately at the beginning of the
step or linearly over the step, depending on the value assigned to the
AMPLITUDE parameter on the STEP option (see Defining an Analysis). If this
parameter is omitted in an Abaqus/Explicit analysis, the reference magnitude is applied immediately at the beginning of the
step.
-
INC
-
This parameter is relevant only when the
FILE parameter is used.
Set this parameter equal to the increment in the selected step of the previous
analysis from which the concentrated nodal fluxes will be read. By default, the
concentrated nodal fluxes will be read from the last increment of the step specified
on the STEP parameter or from the
last step if the STEP parameter is
omitted.
-
OP
-
Set
OP=MOD
(default) for existing CFLUXs to remain, with this
option modifying existing fluxes or defining additional fluxes.
Set
OP=NEW
if all existing CFLUXs applied to the model
should be removed.
-
PHANTOM
-
This parameter applies only to Abaqus/Standard analyses.
Set
PHANTOM=NODE
to apply concentrated fluxes to a phantom node that is originally located coincident
with the specified real node in an enriched element.
Set
PHANTOM=EDGE
to apply concentrated fluxes to a phantom node located on an element edge between the
two specified real corner nodes in an enriched element. This setting applies only to
nodes with both pore pressure and temperature degrees of freedom.
-
REGION TYPE
-
This parameter applies only to Abaqus/Explicit analyses.
This parameter is relevant only for concentrated fluxes applied on the boundary of an
adaptive mesh domain. If concentrated fluxes are applied to nodes in the interior of
an adaptive mesh domain, these nodes will always follow the material.
Set
REGION TYPE=LAGRANGIAN
(default) to apply a concentrated flux to a node that follows the material
(nonadaptive).
Set
REGION TYPE=SLIDING
to apply a concentrated flux to a node that can slide over the material. Mesh
constraints are typically applied to the node to fix it spatially.
Set
REGION TYPE=EULERIAN
to apply a concentrated flux to a node that can move independently of the material.
This option is used only for boundary regions where the material can flow into or out
of the adaptive mesh domain. Mesh constraints must be used normal to an Eulerian
boundary region to allow material to flow through the region. If no mesh constraints
are applied, an Eulerian boundary region will behave in the same way as a sliding
boundary region.
-
STEP
-
This parameter is relevant only when the
FILE parameter is used.
Set this parameter equal to the step number of the previous analysis from which the
concentrated nodal fluxes will be read. By default, the concentrated nodal fluxes will
be read from the last step of the previous analysis.
Data lines to define a concentrated flux
- First line
-
Node number or node set label.
Degree of freedom. If a blank or 0 is entered, degree of freedom 11 is
assumed. For shell heat transfer elements, enter 11, 12, or 13, etc. To specify
ionic fluxes, use degree of freedom 33.
Reference magnitude for flux (units of JT−1 for
heat flux, PL3T−1 for mass flux, and
mol T−1 for ion flux) .
Repeat this data line as often as necessary to define concentrated
fluxes at different nodes and degrees of freedom.
Data lines to define a concentrated heat flux when
PHANTOM=NODE
- First line
-
Node number of a real node that is originally located coincident with the
phantom node.
Degree of freedom. If a blank or 0 is entered, degree of freedom 11 is
assumed.
Reference magnitude for flux (units of JT−1).
Repeat this data line as often as necessary to define concentrated
heat fluxes at different nodes.
Data lines to define a concentrated heat flux when
PHANTOM=EDGE
- First line
-
Node number of one of the two real corner nodes to define an edge in an
enriched element.
Node number of the other real corner node to define an edge in an
enriched element.
Reference magnitude for heat flux (units of
JT−1).
Repeat this data line as often as necessary to define concentrated
heat fluxes at different nodes.