Two connector elements are provided. The element type to be chosen depends on the
dimensionality of the analysis: CONN2D2 for
two-dimensional and axisymmetric analyses and
CONN3D2 for three-dimensional analyses. Both
connector elements have at most two nodes. The position and motion of the second node on the
connector element are measured relative to the first node.
Naming Convention
Connector elements in Abaqus are named as follows:
For example, CONN2D2 is a
two-dimensional, 2-node connector element.
Defining a Connection between Points
A connector element can be used to connect two points.
Input File Usage
ELEMENT, TYPE=nameconnector element number, node_1, node_2
A connector element can be connected to ground, and the ground “node” can be the first or
second point on the connector element. The initial position of the ground node used for
calculating relative position and displacement is the initial position of the other point on
the element. All displacements and rotations at the ground node, if they exist, are fixed.
Input File Usage
Use one of the following options:
ELEMENT, TYPE=nameconnector element number, node number on the bodyELEMENT, TYPE=nameconnector element number, , node number on the body
Abaqus/CAE Usage
Interaction module: ConnectorAssignmentCreate: select wires connected to ground
Components of Relative Motion
Connector elements have relative displacements and rotations that are local to the element.
These relative displacements and rotations are referred to as components of relative motion.
In the three-dimensional case connector elements use 12 nodal degrees of freedom to define
six relative motion components: three displacements and three rotations in element local
directions. In two dimensions six nodal degrees of freedom define three relative motion
components: two displacements and one rotation. The components of relative motion are either
constrained or unconstrained (“available”), depending on the definition of the connector
element.
Constrained Components of Relative Motion
Constrained components of relative motion are displacements and rotations that are fixed
by the connector element.
In connector elements with constrained components of relative motion, Abaqus/Standard uses Lagrange multipliers to enforce the kinematic constraints. Accordingly, in Abaqus/Standard the constraint forces and moments carried by the element appear as additional solution
variables. The number of additional solution variables is equal to the number of
constrained components of relative motion. In Abaqus/Explicit the constraints are enforced using an augmented Lagrangian technique for which no
additional solution variables are needed.
Available Components of Relative Motion
Available components of relative motion are displacements and rotations that are not
constrained kinematically and, hence, remain available for defining material-like
behavior, specifying time-dependent motion, applying loading, or assigning complex
interactions, such as contact or friction. Many connection types have available components
of relative motion, and their meaning is described in
Connection-Type Library for each individual connection type.
Defining the Connection Attributes
The connection attributes define the connector element's function. In the most general case
you specify the following attributes:
the connection type or types,
the local directions associated with the connector's nodes,
additional data for certain connection types, and
the connector behavior.
The connector definition that is defined with these attributes is associated with a set of
connector elements.
Abaqus provides a comprehensive library of connection types. See Connection Types for the available connection types. The connection
types are divided into three categories: basic connection components, assembled
connections, and complex connections. The basic connection components affect either
translations or rotations on the second node. A connector element might include one
translational basic connection component and/or one rotational basic connection component.
The assembled connections are constructed from the basic connection components. They are
provided for convenience and cannot be combined in the same connector element definition
with a basic connection component or other assembled connections. Complex connections
affect a combination of degrees of freedom at the nodes in the connection and cannot be
combined with other connection components.
The connection type is specified as:
a single basic connection type (translational or rotational),
one translational and one rotational basic connection type,
Interaction module:
ConnectorSectionCreate: Connection Category: Basic, Translational type:translational basic connection type and/or Rotational type:rotational basic connection type
or
ConnectorSectionCreate: Connection Category: Assembled/Complex, Assembled/Complex type:assembled connection or complex connection
Defining the Local Connector Directions
Local directions at the nodes are often required to define the connection types used to
define the connector element. The local directions and how they are used to define the
connection are described in Connection Types. In the most general case the connection type uses two sets of
local directions, which are defined as described in Orientations. The names
associated with the two orientation definitions must be referred to from the connector
section definition. Associated orientations can be defined as distributions, and the names
of the distributions must be referred to from the connector section definitions.
Input File Usage
Use the following options for the most general case:
ORIENTATION, NAME=orientation_1ORIENTATION, NAME=orientation_2CONNECTOR SECTION, ELSET=namebasic connection type(s) or assembled connectionorientation_1 for first node (or ground) or the name of the orientation distribution, orientation_2 for second node (or ground) or the name of the orientation distribution
Abaqus/CAE Usage
Interaction module: ConnectorAssignmentCreate: select wires: Orientation 1, Orientation 2: Edit: select the orientations for the first and second points, respectively, of the selected wires
Degree of Freedom Activation and Corotation of Connection Directions
Many connection types either require connection directions at the nodes on the element
or allow optional directions to be defined. In cases where an orientation definition is
permitted for defining connection directions (required or optional), connector elements
activate the rotational degrees of freedom at the nodes to which they are attached, if
they do not exist already. Orientation definitions are allowed for the following basic
translational connection types:
ACCELEROMETER,
CARTESIAN,
PROJECTION CARTESIAN,
RADIAL-THRUST,
SLIDE-PLANE, and
SLOT. Consequently, rotational
degrees of freedom will be activated, if they do not exist already, when any of these
basic translational connection types are used. The only exception is connection type
JOIN, for which connection
directions are optional at the first node of the element, but rotation degrees of
freedom are not activated. Only two basic translational connection types,
LINK and
AXIAL, will ignore the specified
orientation definition at both node a and node
b. Connector elements using one of these two connection types
will not activate rotational degrees of freedom, if they do not exist already.
The connector element's orientation directions corotate with the rotational degrees of
freedom at the corresponding node on the element. If there is no element with rotational
degrees of freedom or rotation constraint (such as an equation or a multi-point
constraint) attached to the node, you must ensure that sufficient rotational boundary
conditions are provided to avoid numerical singularities associated with unconstrained
rotational degrees of freedom. Connection type
JOIN uses fixed directions when
rotational degrees of freedom are not active at the nodes on the connector element.
Example
Figure 1 illustrates the use of the CONN3D2
element to connect two bodies with a cylindrical-like connector oriented at 60° from the
global 1-axis. On the left is a schematic representation of the connection to be
modeled; on the right is a representation of the equivalent finite element model. See Connection-Type Library for a list of connector type names.
Figure 1. Simplified connector model of a shock absorber.
The connection requires node b to remain on the line of the shock
absorber, which is determined by the position and orientation directions of node
a. In addition, the two rotation components perpendicular to the
line of the shock absorber at node b must be the same as those at
node a. Hence, the only relative motion components permitted in the
connection are the displacement of node b relative to node
a along the line of the shock absorber and the rotation of node
b relative to node a about the line of the
shock absorber. This displacement and this rotation are the available components of
relative motion. The connector is defined using the following lines in the input file:
ELEMENT, TYPE=CONN3D2, ELSET=shock
101, 11, 12
CONNECTOR SECTION, ELSET=shock
slot, revolute
ori60,
ORIENTATION, NAME=ori60
**Defines the local 1-direction along the slot (required)
**Also defines the rotation axis for the revolute (required)
0.5, 0.866025, 0.0, -0.866025, 0.5, 0.0
Alternatively, you could use the assembled connection type
CYLINDRICAL instead of the two basic
connection types SLOT and
REVOLUTE.
Defining Additional Connection Type Data
Some connection types allow additional data to define the kinematic behavior of the
connector. For example, the connection type
FLOW-CONVERTER allows you to specify a
scaling factor for material flow at node b. See Connection-Type Library for more information.
Defining the Connector Behavior
Abaqus provides comprehensive kinetic behavior modeling in the available components of
relative motion. Defining connector behavior is optional and can be used to incorporate
spring, dashpot, node-to-node contact, locking, friction, plasticity-like effects, and
failure. The kinetic modeling capabilities in connectors are described in detail in Connector Behavior.
Using Connector Elements in Two-Dimensional and Axisymmetric Analysis
Not all connection types can be used with element type
CONN2D2. The connection-type library contains
many connection types whose mechanics are valid for three-dimensional analyses only. In
other cases the local directions required in the definition of the connection type conflict
with the two-dimensional coordinate system. See Connection-Type Library for more information.
Using Multiple Connector Elements in Parallel
Connector elements in Abaqus allow most physical connections to be modeled with a single connector element. However,
in certain circumstances more complex connections or output considerations might require
multiple connector elements to be used in parallel. This is accomplished by defining two or
more connector elements between the same nodes. In this case you must ensure that a
constrained component of relative motion in one connector element is not constrained (either
by a kinematic constraint or through motion specified as described in Connector Actuation) by one of the other connector elements.
Multiple connector elements are sometimes used in parallel to obtain output in different
coordinate systems. For a connector element between two bodies, the local directions at the
nodes can be determined by the requirements of the connection type. However, output might be
needed in a different, possibly corotating, coordinate system. For example, the angular
acceleration history could be reported in a local, body-fixed coordinate system (other than
the one used to define the connector element) by using a second connector element (such as
connection type CARDAN) that does not
impose kinematic constraints or use connector behavior but aligns with the desired local
output directions.
Defining Connectors in a Model That Contains Parts and an Assembly
An Abaqus model can be defined in terms of an assembly of part instances (see Assembly Definition). Connector
elements can be defined at either the part level or the assembly level in such a model.
Using Connector Elements with Nodal Transformations
Nodal transformations (see Transformed Coordinate Systems) can be defined
for either node connected to the connector element. Since these transformations affect only
the nodal degrees of freedom, their use does not affect the behavior of the connector
element. Connector elements operate on components of motion local to the connection.
Using Nonlinear Connections in Geometrically Linear Analyses
If a connector element with a nonlinear kinematic constraint is used in a geometrically
linear analysis, the kinematic constraint is linearized. For example, if connection type
LINK is used in a geometrically linear
analysis, the distance between the two nodes is held constant after projection onto the
direction of the line between the original positions of the nodes. The difference should be
noticeable only if the magnitudes of the rotations and displacements are not small.
Mismatched Masses at Connector Nodes in Abaqus/Explicit
If the nodes of a connector element in Abaqus/Explicit have masses that are highly mismatched, the implicit solver might encounter convergence
problems due to the resulting ill-conditioned coefficient matrix. To prevent this from
happening, if the nodal masses or rotary inertias of a connector element differ by more than
three orders of magnitude, Abaqus/Explicit adds mass/rotary inertia to the connector element node that has the smaller mass/rotary
inertia. The mass/rotary inertia added is negligibly small (less than three orders of
magnitude smaller) compared to the larger of the connector element's nodal inertias. This
additional mass almost never affects the solution significantly. However, in certain
situations (for example, for a strongly dynamic analysis that has connector elements with
highly mismatched nodal masses) this adjustment might have a noticeable effect.
Connector Output
The connector element force, moment, and kinematic output is defined in Connector Element Library. These output quantities include total, elastic,
viscous, and friction forces and moments. In addition, reaction forces and moments caused by
connector stops and locks are available as well as connector contact forces used for
friction calculation.
To obtain accurate reaction force and moment output for connectors from Abaqus/Explicit, it might sometimes be necessary to run the analysis in double precision. In such
situations a double precision run will also yield a better estimate of the work done by the
reaction forces and moments, thereby providing a more accurate value of the energy due to
the external work reported by Abaqus/Explicit.
Kinematic output includes relative position, relative displacement, relative velocity,
relative acceleration, frictional slip, and constitutive displacements (the displacement
used in the elastic force and hysteretic friction calculations defined as the difference
between the current relative positions and the reference positions; see Defining Reference Lengths and Angles for Constitutive Response). For
relative rotations the Abaqus convention of reporting angles between and radians is not used with connector elements. Connector element output of
angles and rotational components or relative motion includes accumulated multiple rotations
whose magnitudes can be arbitrarily large. Energy output is available, as are output flags
to identify whether a connector has failed (in Abaqus/Explicit only), locked, or reached a connector stop.
In modal analysis procedures, element output is allowed only for the
AXIAL,
BUSHING,
CARDAN,
CARTESIAN, and
ROTATION connection types when there is
no connector motion associated with them.
In a geometrically linear step in Abaqus/Standard the relative position output variable does not change (in the same fashion that the nodal
coordinates are output). Therefore, care must be exercised in interpreting output for
connector stops and locks since they use updated coordinates.
In implicit dynamic problems, the output of some connector forces and moments can be noisy,
especially at the beginning of dynamic steps.
Connector element names displayed in the output database have a "G" added at the end to
indicate that this connector is connected to ground.
Using Connector Elements for Output Only
Connector elements defined without kinematic constraints or constitutive behavior can be
used to monitor kinematic output in local coordinate systems. Quantities of interest include
relative position, displacement, velocity, and acceleration in local coordinate
parametrization. Finite rotation parameterizations include Euler and Cardan angles, rotation
vector, and flexion-torsion-sweep. For an example that uses a connector element to monitor
Euler angles, see Motion of a rigid body in Abaqus/Standard.
In Abaqus/Explicit all such connectors are solved without invoking the implicit solver, which leads to
better performance in domain parallel mode (particularly when such connectors nodes overlap
with other constraints such as secondary nodes of tie constraints).