The particle generator capability enables a modeling approach in which the discrete element
method considers particles only after entering a region of interest. This approach can
simplify model set-up and improve computational efficiency. Characteristics of this
capability include:
particles are generated at an inlet that can vary in shape over time,
generated particles can have random sizes based on a user-specified probability density
function,
multiple species of particles can be generated simultaneously by a single generator,
and
the net mass flow rate and particle speeds at the inlet can be specified with time
dependence.
Applications
How you use the particle generator will depend on the process being analyzed. Two broad
usage categories are as follows:
Model creation
In many applications the particle generator can be used to fill part of a domain
with particles to establish initial conditions for subsequent studies. Figure 1 shows an example where two particle generators are filling a drum mixer with two
different batches of particles prior to performing a mixing simulation. The sequence
of images show the start and end of the particle generation phase.
Figure 1. Model creation using particle
generator.
Continuous generation
In another type of application a particle generator can be used to inject a
continuous stream of particles into the domain while an event of interest involving
particles that have been introduced is underway. Figure 2 shows the use of a particle generator in a sorting analysis. In this application a
particle generator is continuously feeding random sized particles to a screen sorter
assembly while the analysis is in progress.
Figure 2. Continuous particle generation example.
Defining a Particle Generator
To define a particle generator, you specify a name for the generator, the type of particle
to be generated, and the maximum number of particles that might be generated during the
analysis. You must define an inlet surface, the list of particle species that will be
generated, and the size distribution for each species.
In many processes the number and speed of the particles being introduced into the domain
are not constant during the analysis. You must define the time-dependent mass flow rate per
unit inlet area and the particle speed at the generator inlet to control the rate of
injection of particles of each species through the inlet. These specifications allow the
possibility of turning the particle generator on or off during the analysis.
Input File Usage
PARTICLE GENERATOR, NAME=generator_name, TYPE=PD3D,
MAXIMUM NUMBER OF PARTICLES=number
Inlet Surface
The inlet surface can be thought of as an opening through which the particles are
injected into the domain. It is important that no other model feature is positioned in
front of the generator inlet to obstruct the flow of particles. An element-based surface
must be defined for the inlet surface. Using surface elements is appropriate in most
applications. Care should be taken with respect to the positive surface normal direction
at the inlet because the initial particle velocity will be in this direction. A complex
inlet geometry as shown in Figure 3 might have several facets. In this example the normal direction to the inlet surface is
out of the page.
Figure 3. Complex inlet geometry with multiple facets.
The size and shape of the inlet surface can be modified during an analysis by adjusting
the nodal positions of the inlet surface. The inlet surface can expand, collapse, and
translate as well as undergo rigid body motions. Figure 4 shows the inlet surface of four different generators being subjected to different
deformation and motion.
Figure 4. Expanding, translating, rotating, and skewing an inlet surface.
In many applications several different types of particles interact with each other. For
example, sand, cement, and aggregate particles are mixed together to prepare a batch of
concrete. A particle generator can be used to generate one or more species of particles as
shown in Figure 5, where the two colors represent the two species of particles that have been
simultaneously generated by a particle generator. An element set name is associated with
each species in the mixture. This is analogous to a regular
DEM analysis where the particles are grouped into
element sets.
Statistical distributions are commonly used to specify the particle sizes. Statistical
distributions are defined by analytical or user-specified piecewise linear tabular
probability density functions (PDF). The particle
generator supports the following different types of probability density functions:
uniform, normal, log-normal, and piecewise linear. The normal and log-normal
PDFs have well-known analytical forms that depend on
the mean and standard deviation of the random deviate. In some cases the particle size
distribution might be obtained from sieving particle samples in the field. These data are
usually in the form of a table of size ranges and the percentages of particles that fall
within those size ranges (a histogram). The piecewise linear
PDF can be used for such data. See Probability Density Function for further
details on the usage of probability density functions.
Mass Flow Rate
The rate of generation of particles is governed by the specified mass flow rate per unit
area at the inlet, the area of the inlet, and the ability of the generator to insert a
particle of a given size. The time varying mass flow rate per unit inlet area, , has the units . For a multiple species particle generator the total mass flow rate per
unit inlet area is the sum of the mass flow rates per unit inlet area of the individual
species:
The time varying mass flow rate per unit inlet area for each species must be provided in
the form of an amplitude table (Amplitude Curves).
Input File Usage
PARTICLE GENERATOR FLOW, GENERATOR=generator_name
, mass flow rate amplitude for species 1, mass flow rate amplitude for species 2, etc.
Particle Speed
For a given particle generator, particles of all species are introduced into the domain
through the inlet with a specified flow speed. The flow direction of the particles is
along the normal to the inlet facet. Particles generated from different facets in the
inlet surface will all have the same flow speed; however, depending on the facet normal
direction, they may have different velocities. The time varying particle flow speed must
be provided in the form of an amplitude table (Amplitude Curves).
The current coordinates of the nodes of each facet in the inlet surface are used to define
a plane (a generation plane) where particles will be generated. Figure 6 shows the local directions of the generation plane. The first local direction, , is defined by the longest facet edge, while , the third local direction, is normal to the facet. The normal to the
facet is obtained from the cross-product of the diagonal vectors (the vector joining nodes 2
and 4 and the vector joining nodes 1 and 3; see Figure 6 for local node numbers). The second in-plane direction is . The plane of generation is positioned in front of the inlet facet, where is the smallest particle radius for the generator.
Figure 6. Particle generation plane.
The in-plane particle coordinates of a particle are generated randomly according to a
uniform random distribution. The generated in-plane coordinates are acceptable if the
particle can be placed at that location ensuring that it does not overlap with previously
generated particles and also does not intersect the boundaries defined by the facet edges.
Assigning Properties to Particles
Particles of different species will have different size distribution, density, and contact
properties. To assign a density and size distribution for a particle species, the
corresponding element set name is specified on a section definition for the
PD3D elements. The element set name is also
used to define a surface that is referred to under the contact specifications. This way of
assigning particle properties and contact properties for generated particles is no different
from what is done for user-defined sets of discrete particles. See Discrete Element Method for details on how to assign properties to
PD3D elements and how to set up contact
definitions for a DEM analysis.
Particle Size Rejection
Abaqus/Explicit discards particle sizes that are outside the specified minimum and maximum range for the
PDF. For normal and log-normal type
PDFs this leads to a truncated distribution, as explained
in Probability Density Function. Keep this in
mind when comparing the generated particle size distribution to the target
PDF.
A generated particle size is discarded if it is too large to fit through the current inlet
geometry. It is possible that the generator might fail to place a particle in the randomly
generated location in the generation plane if there is not sufficient room to accommodate
the newly generated particle size. If this happens, the generator will generate another
random location and attempt to place the particle there. By default, 15 such attempts will
be made, after which the particle size is discarded and another particle size is randomly
generated and the process is repeated. You can modify the default number of attempts to
place a generated particle size.
If particle sizes are rejected because of either of the above reasons, the generated size
distribution cannot be guaranteed to match the specified size distribution. Figure 7 shows a comparison of generated and specified piecewise linear particle size
distributions for a specific problem where 14608 particles were generated at a constant mass
flow rate and with constant particle speed through an inlet of fixed geometry. The overall
agreement of the generated particle size distribution is good even though the generator was
unable to insert some particles into the domain.
Figure 7. Comparison of specified and generated discrete particle size distributions.
At any increment, k, corresponding to the end of increment time, , and time increment size, , the specified mass of particles of species, i, to be
generated is
where is the current inlet facet area. Due to the discrete nature of the time
increment and particle sizes, the particle generator will not be able to match the specified
mass exactly for the species for the given increment. The particle generator, therefore,
maintains a mass balance for each species. For a given species a negative mass balance
indicates that for that species the mass of particles generated was higher than what was
required. The excess mass balance for species, i, from the previous
increment is taken into account while computing the target mass to be generated in
the current increment:
The mass balance for species i for the current increment is
where is the actual mass of the particles generated in increment
k. The particle generator tries to match the specified mass flow rate
per unit inlet area as closely as possible. If the target mass for a species is negative
because of a high negative mass balance, no particles will be generated for that species
until the target mass becomes positive again. Figure 8 shows a comparison of generated and specified mass flow rate for a specific problem where
the specified mass flow rate per unit inlet area does not vary with time and the inlet
geometry is fixed.
Figure 8. Comparison of specified and generated mass flow rate.
Inlet Blocking
The flow speed, , and mass flow rate per unit inlet area, , are related as follows:
where is the particle density and is the solid fraction. The solid fraction is the ratio of the volume of
particles to the volume of the region they occupy. This relation suggests that the packing
of particles ahead of the inlet increases for a given mass flow rate per unit inlet area as
the flow speed is reduced. If this happens, the particle generator will take many more
attempts to insert a particle. Therefore, a meaningful specification of flow speed for a
given mass flow rate per unit inlet area is crucial for the efficiency of the particle
generator. It is also important that no other model feature is positioned in front of the
generator inlet to obstruct the flow of particles.
Automatic Halting of Particle Generator
A particle generator will permanently halt after generating the maximum number of
particles. Since it might be difficult to make an accurate estimation of the total number of
particles that need to be generated during an analysis, overestimating the maximum number of
particles will ensure that a particle generator will not run out of particles. However,
grossly overestimating the maximum number of particles will lead to larger memory
requirements for the analysis.
The particle generator will temporarily halt for an increment if the region near the inlet
has a high volume fraction of particles. This helps avoid performance degradation due to an
excessive number of failed attempts to insert a new particle when the inlet is becoming
clogged with existing particles. The default threshold for a temporary halt to the generator
is a particle volume fraction of 0.4 over a volume that extends in front of the inlet surface, where is the maximum particle radius for the generator. You can modify the
default value of the solid fraction used for halting the generator.
It is possible that the current inlet geometry and the particle size distribution is such
that the particle generator repeatedly exhausts the 15 attempts to insert a particle of a
given size. If 10 such cycles of 15 attempts each have been unsuccessful in a given
increment, the generator will temporarily halt generation. You can modify the default value
of 10 cycles prior to halting particle generation.
Input File Usage
PARTICLE GENERATOR, SOLID FRACTION=threshold solid fraction,
MAX ATTEMPTS PER INCREMENT=number of insertion attempts cycles
Initial Conditions
Initial conditions should not be applied to nodes of particle species.
Boundary Conditions
Boundary conditions can be applied to the nodes of the inlet facet to expand, shrink, or
move the inlet facets of a generator.
Loads
The element set name for a species can be used to apply loads such as gravity or body
loads.
Elements
The particle generator generates PD3D and
PC3D elements.
Constraints
Constraints such as multi-point constraint type BEAM
can be applied to the nodes of inlet facets to facilitate the application of rigid body
motion to the inlet facet of a generator.
Interactions
Contact interactions between particle species are specified similar to user-defined
PD3D elements. You must not include the inlet
facets in the contact domain.
Output
Output is available for the element sets and node sets generated by the particle generator.
Limitations
The following limitations apply to analyses involving the particle generator:
Only PD3D and
PC3D elements can be generated.
It is not possible to generate clusters of
PD3D elements.
Although supported in Abaqus/Viewer, the functionality is not supported in Abaqus/CAE.
Input File Template
The following example illustrates a particle generator with two particle species: