Specifying Progressive Element Activation and Scan Pattern Parameters
The layer-by-layer deposition of raw material from a recoater or roller blade is simulated using progressive element activation in a structural or a thermal analysis. The following steps are required to define the deposition process and scan pattern parameters completely:
- Create a table collection with a name that begins with "ABQ_TMP". The table collection must contain a parameter table of type "ABQ_AM_ThermoMech_PatternBased_Activation" as well as the other parameter tables listed below.
- Define the build parameters (such as slice or layer thickness and build coordinate system) in a parameter table of type "ABQ_AM_ThermoMech_PatternBased_Activation".
- Define the laser power, scan spacing, and speed in a parameter table of type ABQ_AM_ThermoMech_ScanParameter_Define.
- Define parameters of rectangular patches that make up a rectangular unit cell (see Scan Pattern–Mesh Intersection), which is repeated to cover the cutting plane or a layer, in a parameter table of type ABQ_AM_ThermoMech_PatternBased_Define. You can define the following parameters: a local angle, ; the extents of a patch and ; and a label of the parameter table of type ABQ_AM_ThermoMech_ScanParameter_Define defining laser power and other scan parameters to apply to this patch.
-
Define the parameters of the bounding box, inside which a particular scan-pattern strategy is active, in a parameter table of type ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define.
Alternatively, use a parameter table of type ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define_Elset to assign a particular scan-pattern strategy directly to an element set. Element set–based assignments of scan-pattern strategies have precedence over bounding box–based assignments.
You can combine both assignment types under the same table collection.
- List the names of all the parameter tables of types ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define and ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define_Elset defining all active strategies in a table of type "ABQ_AM_ThermoMech_PatternBased_ScanStrategies".
- As described above, you must define at least one parameter table of each of the following types: "ABQ_AM_ThermoMech_PatternBased_Activation", "ABQ_AM_ThermoMech_PatternBased_Activation", "ABQ_AM_ThermoMech_PatternBased_Define", "ABQ_AM_ThermoMech_PatternBased_ScanStrategies", and either "ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define" or "ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define_Elset".
- Optionally, define parameter tables of types ABQ_AM_ThermoMech_PatternBased_Advanced and ABQ_AM_ThermoMech_Activation_Advanced to specify advanced options.
- Refer to the table collection when you turn on the progressive element activation feature. You can include only one option to turn on progressive element activation in an analysis.
Abaqus/Standard activates elements automatically according to the specified pattern parameters and automatically estimates the printing time of each layer. Abaqus/Standard assigns a local orientation for anisotropic materials to elements at the time of activation based on the pattern definition. You must define an initial local orientation and refer to it from the section definition for the elements that use an anisotropic material.
A dedicated collection of parameter table, property table, and event series types is available to include all the definitions required by special-purpose techniques for additive manufacturing. These special-purpose parameter table, property table, and event series type definitions are generated internally. You need to explicitly include them in your model only if you output the results of your additive manufacturing simulation in SIM format. If needed, you can use the abaqus fetch utility to obtain the file containing all the type definitions of parameter tables, property tables, and event series required by the special-purpose techniques for additive manufacturing as follows:
abaqus fetch job=ABQ_am_special_purpose_types.inp
Input File Usage
Use the following options to define progressive element activation and scan parameters in a thermal or a structural analysis:
TABLE COLLECTION, NAME="ABQ_TMP_Activation 1" PARAMETER TABLE, TYPE="ABQ_AM_ThermoMech_PatternBased_Activation" , coordinates defining the build system , recoater time, print start time, TOTALTIME / STEPTIME PARAMETER TABLE, TYPE="ABQ_AM_ThermoMech_ScanParameter_Define", LABEL = "Island 1" Power, scan spacing, speed, on time fraction include as many parameter tables of type ABQ_AM_ThermoMech_ScanParameter_Define as needed PARAMETER TABLE, TYPE="ABQ_AM_ThermoMech_PatternBased_Define", LABEL="Pattern 1" , label of a table of type ABQ_AM_ThermoMech_ScanParameter_Define such as "Island 1", additional data lines to define more patches PARAMETER TABLE, TYPE="ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define", LABEL="Scan region box1" label of a table of type ABQ_AM_ThermoMech_PatternBased_Define such as "Pattern 1", , include as many parameter tables of type PARAMETER TABLE, TYPE="ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define_Elset", LABEL="Scan region elset1" label of a table of type ABQ_AM_ThermoMech_PatternBased_Define such as "Pattern 1", , element set name include as many parameter tables of type ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define as needed PARAMETER TABLE, TYPE="ABQ_AM_ThermoMech_PatternBased_ScanStrategies" list of labels of parameter tables of types ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define and ABQ_AM_ThermoMech_PatternBased_ScanStrategy_Define_Elset such as "Scan region box1" and "Scan region elset1" in the analysis PARAMETER TABLE, TYPE="ABQ_AM_ThermoMech_Activation_Advanced" "Full" or "Partial", min volume fraction threshold for partial activation, max volume fraction threshold for partial activation, volume fraction threshold for full activation ... ELEMENT PROGRESSIVE ACTIVATION, NAME=activation name, ELSET=element set name ... STEP STATIC or HEAT TRANSFER ... ACTIVATE ELEMENTS, ACTIVATION=activation name "ABQ_TMP_Activation 1" ...