*STEP CONTROL

Control progress of the simulation based on the solution state.

This option is used to control the progress of a simulation based on the solution state. If you specify a threshold value for a particular measure of the solution state that has been associated with a sensor definition, the action taken on reaching the threshold can include terminating the current step or terminating the analysis.

You can define an action for a step control to end the current step or analysis when the algebraic or the absolute value of the sensor has reached either a maximum or a minimum threshold. You can also specify that Abaqus/Standard utilizes an alternative time incrementation that is smaller than that computed by the normal time-incrementation algorithms in Abaqus/Standard when the sensor value falls within a user-specified range.

The STEP CONTROL option applies only in the step in which it is defined. You can define multiple STEP CONTROL definitions within a single step.

This page discusses:

See Also
*STEP
In Other Guides
Defining an Analysis

Products Abaqus/Standard

Type History data

LevelStep

Required parameters

NAME

Set this parameter equal to the name associated with this sensor-based step control definition. The sensor’s name itself is given on the data line.

Optional parameters

ACTION

By default, the step control definition is utilized for time increment refinement when the value of the sensor is within a specified interval. In this case, no threshold value of the sensor is necessary. The nondefault actions of a step control definition require the specification of a threshold value of the sensor.

Set ACTION=CONTINUE (default) to trigger time increment refinement when the value of the sensor is within a specified interval. It must be used in conjunction with DT REFINEMENT=YES.

Set ACTION=END ANALYSIS to end the analysis completely when the sensor reaches a specified threshold value.

Set ACTION=END STEP to conclude the current step and to continue to the next step when the sensor reaches a specified threshold value.

DT REFINEMENT

You can specify two limits and control the time incrementation when the sensor value is within the range defined by the two limits to get finer resolution on the solution within a specified range of values for the sensor while using normal time increments outside of this range. Alternatively, you can specify a limit and a threshold value and control the time incrementation when the sensor value is in that range.

Set DT REFINEMENT=AUTO to indicate that Abaqus/Standard should refine the time increment automatically to reach the threshold as closely as possible.

Set DT REFINEMENT=NO to leave the time increment unaffected.

Set DT REFINEMENT=YES (default) to indicate that a user-specified fixed time increment should be used.

TOLERANCE

Set this parameter equal to the tolerance to be used to determine when the sensor has reached the threshold value. The TOLERANCE parameter must be used in conjunction with DT REFINEMENT=AUTO.

Abaqus/Standard enforces the relative error in the sensor value with respect to its threshold value to be less than the specified tolerance. The default value of the tolerance is 0.001.

Data lines to define a sensor-based step control to end the current step or the analysis without refining the time incrementation (DT REFINEMENT=NO, ACTION=END STEP or ACTION=END ANALYSIS)

First data line
  1. Sensor name.

  2. Threshold criteria (Max, Min, AbsMax, or AbsMin).

  3. Sensor threshold value.

Repeat this data line as often as necessary to define different stopping criteria, potentially using different sensors.

Data lines to define a sensor-based step control to end the current step or the analysis with automatic refinement of the time incrementation (DT REFINEMENT=AUTO, ACTION=END STEP or ACTION=END ANALYSIS)

First data line
  1. Sensor name.

  2. Threshold criteria (Max, Min, AbsMax, or AbsMin).

  3. Sensor threshold value.

Repeat this data line as often as necessary to define different stopping criteria, potentially using different sensors.

Data lines to define a sensor-based step control to end the current step or the analysis with a user-specified refinement of the time incrementation (DT REFINEMENT=YES, ACTION=END STEP or ACTION=END ANALYSIS)

First data line
  1. Sensor name.

  2. Threshold criteria (Max, Min, AbsMax, or AbsMin).

  3. Sensor threshold value.

  4. Time increment value to be used, provided that it is lower than the time increment computed by the automatic time-incrementation algorithms in Abaqus/Standard and the condition for time increment refinement is met.

  5. Sensor limit value when the time increment refinement starts.
  6. Blank.

Repeat this data line as often as necessary to define different stopping criteria, potentially using different sensors.

Data lines to define a sensor-based step control, with a user-specified refinement of the time incrementation, to get a finer resolution of the solution within a specified interval (DT REFINEMENT=YES, ACTION=CONTINUE)

First data line
  1. Sensor name.

  2. Blank.

  3. Blank.

  4. Time increment value to be used, provided that it is lower than the time increment computed by the automatic time-incrementation algorithms in Abaqus/Standard and the condition for time increment refinement is met.

  5. Sensor limit value when the time increment refinement starts.
  6. Sensor limit value when the time increment refinement ends.

Repeat this data line as often as necessary to refine the time increment in regions of interest, potentially using different sensors.