-
ADJUST ORIENTATION
-
Set
ADJUST ORIENTATION=YES
(default) to have Abaqus adjust the user-defined orientation such that the local
z-axis for each fastener is normal to the
surface that is closest to the reference node for that fastener.
Set
ADJUST ORIENTATION=NO
to define the local directions precisely.
-
ATTACHMENT METHOD
-
Set this parameter equal to the projection method to be used to find the
fastening points for the fastener.
Set
ATTACHMENT METHOD=FACETOFACE
(default) to select the default projection method of locating fastening
points on the specified surface or surfaces. The positioning point is
projected onto the nearest surface to create the first fastening point,
and normal projection is used to find subsequent fastening points.
Set
ATTACHMENT METHOD=FACETOEDGE
to find the first fastening point by projecting the normal on the
nearest surface and to find subsequent fastening points at the closest
points on the specified surface or surfaces.
Set
ATTACHMENT METHOD=EDGETOFACE
to find the closest point on the nearest surface as the first fastening
point and to find subsequent fastening points via normal projections on
the remaining surfaces.
Set
ATTACHMENT METHOD=EDGETOEDGE
to find the closest fastening points on the specified surface or
surfaces.
Set
ATTACHMENT METHOD=CONNECTORDIRECTION
to establish fastening points on the respective surfaces based on the
axial direction of the connector element associated with the fastener.
This option is valid only if the
ELSET parameter is
specified without the
REFERENCE NODE SET
parameter and the specified nodal positions for the connector element
are not co-located.
-
COUPLING
-
This parameter controls whether the rotations of surface nodes
participate in translational coupling constraints for each fastening
point.
Set
COUPLING=CONTINUUM
(default) to couple the displacement and rotation of each fastening
point to the displacement (but not rotation) of the surface nodes within
the radius of influence.
Set
COUPLING=STRUCTURAL
to couple the displacement and rotation of each fastening point to the
displacement and rotation of the surface nodes within the radius of
influence.
-
NUMBER OF LAYERS
-
Set this parameter equal to the number of layers for each fastener. If
this parameter is omitted and no surface is specified by the user or a
single surface is specified by the user, Abaqus will form the maximum possible number of layers for each
fastener.
This parameter is ignored if multiple surfaces are specified on the data
lines.
-
ORIENTATION
-
Set this parameter equal to the name of an orientation definition (see
Orientations) that defines the orientation of the
fastener. If this parameter is omitted, the orientation of each fastener
is determined from the default local directions of the surface (see
Conventions) that is closest to the reference node
for that fastener.
Fasteners support only rectangular, cylindrical, and spherical
orientation definitions. Additional rotations defined as part of the
orientation definition are ignored.
-
RADIUS OF INFLUENCE
-
Set this parameter equal to the maximum distance from the projection
point on a connected surface within which the nodes on that surface must
lie to contribute to the motion of the projection point. If this
parameter is omitted, Abaqus will compute a default value of the radius of influence internally,
based on the fastener diameter and the surface facet lengths.
-
ROTATIONAL COUPLING
-
This parameter controls whether the displacement and the rotation of
surface nodes participate in rotational coupling constraints for each
fastening point.
Set
ROTATIONAL COUPLING=AUTOMATIC
(default) to allow Abaqus to couple the rotation of each fastening point to the displacement
and, if needed, rotation of the surface nodes within the radius of
influence.
Set
ROTATIONAL COUPLING=CONTINUUM
to couple the rotation of each fastening point to the displacement (but
not rotation) of the surface nodes within the radius of influence.
Set
ROTATIONAL COUPLING=STRUCTURAL
to couple the rotation of each fastening point to the displacement and
rotation of the surface nodes within the radius of influence.
-
SEARCH RADIUS
-
Set this parameter equal to the distance from the reference nodes within
which the connected points must lie. If this parameter is omitted and no
surface is specified by the user or a single surface is specified by the
user, Abaqus will compute a default search radius based on the facet thickness
(for shell element facets) or characteristic facet length (for non-shell
element facets) in the vicinity of each positioning point.
-
UNSORTED
-
If this parameter is omitted, the connectivity of the fastening points is
defined by the relative positions of their associated surfaces along the
fastener projection direction.
If this parameter is included, the connectivity of the fastening points
is defined by the order in which their associated surfaces appear on the
data lines.
This parameter is ignored if no surfaces are specified on the data
lines.
-
WEIGHTING METHOD
-
Set this parameter equal to the weighting scheme to be used to weight the
contribution of the displacements of the surface nodes within the radius
of influence to the motion of the fastener projection point.
Set
WEIGHTING METHOD=UNIFORM
(default) to select a uniform weight distribution.
Set
WEIGHTING METHOD=LINEAR
to select a linear decreasing weight distribution.
Set
WEIGHTING METHOD=QUADRATIC
to select a quadratic polynomial decreasing weight distribution.
Set
WEIGHTING METHOD=CUBIC
to select a cubic polynomial monotonic decreasing weight
distribution.