Trajectory-based eigenstrain analysis

This problem contains basic test cases for one or more Abaqus elements and features.

This page discusses:

Products Abaqus/Standard

Eigenstrain analysis using a fixed tool orientation

Elements tested

C3D8

Features tested

Trajectory-based eigenstrain approach for additive manufacturing simulation with the tool orientation fixed in the Z-direction and fixed deposition bead height and width.

Problem description

This model demonstrates how Abaqus/Standard uses the trajectory-based eigenstrain method for additive manufacturing simulations. It assumes a fixed tool orientation along the Z-direction during the simulation. The height and width of the deposition bead are also fixed.

The geometry of this model consists of two distinct parts: a rectangular frame that includes all the elements to be activated and a fixed rigid part acting as a support to the elements to be activated. The bottom surface of the frame is tied to the top surface of the support part. A linear elastic material definition with an orientation initially aligned to the global coordinate system is assigned to the elements to be activated representing the frame part. The simulation updates the material orientation for the activated elements to align with the tool trajectory so that the ε 11 * eigenstrain tensor component is along the tool path.

The model definition follows the steps provided in "Specifying Element Activation and Eigenstrain Using the Trajectory-Based Method".

In the initial configuration, the elements representing the frame are not active. During the simulation, the tool moves along a trajectory following the frame. Two counterclockwise loops stacked in the Z-direction are defined in event series type "ABQ_AM_HeatSourceTrajectory_RuleID". In this event series, the tool is turned off when it is repositioned vertically (that is, in the stack direction) for the second loop. Four eigenstrain tensors are defined in the table collection and the provided event series, allowing a different eigenstrain to be applied to the activated elements on each side of the frame. The deposition bead is positioned below the trajectory defined in the event series.

Figure 1. Applied eigenstrain 11-component (along the tool trajectory) in the activated elements.

Figure 2. Material orientation after element activation.

Results and discussion

The results provided by running this model indicate that the elements are activated as expected, based on the provided tool trajectory. The applied eigenstrains (once the elements are activated) are consistent with the definitions provided in the table collection used by this model and specification provided in the event series.

Eigenstrain analysis using a time-dependent tool orientation and bead dimensions

Elements tested

C3D20R

Features tested

Trajectory-based eigenstrain approach for additive manufacturing simulation with time-dependent tool orientation and time-dependent deposition bead height and width.

Problem description

This model demonstrates how Abaqus/Standard uses the trajectory-based eigenstrain approach for additive manufacturing simulations. It assumes a time-dependent tool orientation is employed during the simulation. The height and width of the deposition bead are also time-dependent.

The geometry of this model consists of two distinct parts: a three-dimensional frame that includes all the elements to be activated and four fixed rigid supports The bottom corner regions of the frame are tied to the top surfaces of the rigid supports. A linear elastic material definition with an orientation initially aligned to the global coordinate system is assigned to the elements to be activated representing the frame part. The material orientation for the activated elements is updated during simulation to be aligned with the tool trajectory so that the ε 11 * eigenstrain tensor component is along the tool path.

The model definition follows the steps provided in "Specifying Element Activation and Eigenstrain Using the Trajectory-Based Method".

Figure 3. Applied eigenstrain 11-component (along the tool trajectory) in the activated elements.

In the initial configuration, the elements representing the frame are not active. During the simulation, the tool moves along a trajectory defined using event series type "ABQ_AM_EigenStrain_TrajectoryBased_5AxisStrategy_VariableCrossSection". In the event series used in this model, the tool orientation is modified during the activation of the vertical columns and the top portion of the frame. Three different eigenstrain definitions (rules) are used in the model for the bottom layer, vertical columns, and top layer of the frame. The event series also includes time-dependent height and bead dimensions. The deposition bead is centered on the trajectory defined in the event series.

Results and discussion

Results of this model verify that the element activation aligns with the tool trajectory, tool orientation, and bead dimensions specified as part of the event series. The applied eigenstrains, once the elements are active, are consistent with the definitions provided in the table collection used by this model and the specification in the event series.