is intended to provide a simple continuum model for a material containing a high density
of parallel joint surfaces where each system of parallel joints is associated with a
particular orientation, such as sedimentary rock;
assumes that the spacing of the joints of a particular orientation is sufficiently close
compared to characteristic dimensions in the domain of the model such that the joints can
be smeared into a continuum of slip systems;
provides for opening or frictional sliding of the joints in each of these systems (a
“system” in this context is a joint orientation in a particular direction at a material
calculation point); and
assumes that the elastic behavior of the material is isotropic and linear when all joints
at a point are closed (isotropic linear elastic behavior must be included in the material
definition; see Defining Isotropic Elasticity).
The jointed material model is intended primarily for applications where the stresses are
mainly compressive. The model provides a joint opening capability when the stress normal to
the joint tries to become tensile. In this case the stiffness of the material normal to the
joint plane becomes zero instantaneously. Abaqus/Standard uses a stress-based joint opening criterion, whereas joint closing is monitored based on
strain. Joint system a opens when the estimated pressure stress across
the joint (normal to the joint surface) is no longer positive:
In this case the material is assumed to have no elastic stiffness with respect to direct
strain across the joint system. Open joints thus create anisotropic elastic response at a
point. The joint system remains open so long as
where is the component of direct elastic strain across the joint and is the component of direct elastic strain across the joint calculated in
plane stress as
where E is the Young's modulus of the material, is the Poisson's ratio, and , are the direct stresses in the plane of the joint.
The shear response of open joints is governed by the shear retention parameter, , which represents the fraction of the elastic shear modulus retained when
the joints are open (=0 means no shear stiffness associated with open joints, while =1 corresponds to elastic shear stiffness in open joints; any value between
these two extremes can be used). When a joint opens, the shear behavior might be brittle,
depending on the shear retention factor used for open joints. In addition, the stiffness of
the material normal to the joint plane suddenly goes to zero. For these reasons, in
situations where the confining stresses are low or significant regions experience tensile
behavior, the joint systems might experience a sequence of alternate opening and closing
states from iteration to iteration. Typically such behavior manifests itself as oscillating
global residual forces. The convergence rate associated with such discontinuous behavior
might be very slow and, thus, prohibit obtaining a solution. This type of failure is more
probable in cases where more than one joint system is modeled.
Improving Convergence When Joints Open and Close Repeatedly
When the repeated opening and closing of joints makes convergence difficult, you can
improve convergence by preventing a joint from opening. In this case an elastic stiffness
is always associated with the joint. It is most useful when the opening and closing of
joints is limited to small regions of the model. You can prevent a joint from opening only
when the joint direction is specified, as described below.
You must specify nonzero shear retention in open joints directly. The parameter can be defined as a tabular function of temperature and predefined field
variables.
The failure surface for sliding on joint system a is defined by
where is the magnitude of the shear stress resolved onto the joint surface, is the normal pressure stress acting across the joint, is the friction angle for system a, and is the cohesion for system a. So long as , joint system a does not slip. When , joint system a slips. The inelastic (“plastic”)
strain on the system is given by
where
is the rate of inelastic shear strain in direction on the joint surface ( are orthogonal directions on the joint surface),
is the magnitude of the inelastic strain rate,
is a component of the shear stress on the joint surface,
is the dilation angle for this joint system (choosing provides pure shear flow on the joint, while causes dilation of the joint as it slips), and
is the inelastic strain normal to the joint surface.
The sliding of the different joint systems at a point is independent, in the sense that
sliding on one system does not change the failure criterion or the dilation angle for any
other joint system at the same point.
Up to three joint directions can be included in the material description. The orientations
of the joint directions are given by referring to the names of user-defined local
orientations (Orientations) that define the
joint orientations in the original configuration. Output of stress and strain components is
in the global directions unless a local orientation is also used in the material's section
definition.
The parameters , , and can be specified as tabular functions of temperature and/or predefined
field variables for each joint direction.
Repeat the JOINTED MATERIAL option for each
direction to be specified, up to three times.
Joint Directions and Finite Rotations
In geometrically nonlinear analysis steps the joint directions always remain fixed in
space.
Bulk Failure
In addition to the joint systems, the jointed material model includes a bulk material
failure mechanism, which is based on the Drucker-Prager failure criterion:
where
is the Mises equivalent deviatoric stress,
is the deviatoric stress,
is the equivalent pressure stress,
is the friction angle for the bulk material, and
is the cohesion for the bulk material.
If this failure criterion is reached, the bulk inelastic flow is defined by
where
is the flow potential. Here is the magnitude of the inelastic flow rate (chosen so that in uniaxial compression in the 1-direction), and is the dilation angle for the bulk material. This bulk failure model is a
simplified version of the extended Drucker-Prager model (Extended Drucker-Prager Models). This bulk failure system is independent of the
joint systems in that bulk inelastic flow does not change the behavior of any joint
system.
If bulk material failure is to be modeled, a jointed material behavior must be specified to
define the parameters associated with bulk material failure behavior. Thus, up to five
jointed material behaviors can appear in the same material definition: three joint
directions, shear retention in open joints, and bulk material failure.
The parameters , , and can be specified as a tabular function of temperature and/or predefined
field variables.
Input File Usage
JOINTED MATERIAL (the JOINT DIRECTION parameter must be omitted)
Nonassociated Flow
If in any joint system, whether it be associated with the joint surfaces or
the bulk material, the flow in that system is “nonassociated.” The implication is that the
material stiffness matrix is not symmetric. Therefore, the unsymmetric matrix solution
scheme should be used for the analysis step (Defining an Analysis), especially
when large regions of the model are expected to flow plastically and when the difference
between and is large. If the difference between and is not large, a symmetric approximation to the matrix can provide an
acceptable rate of convergence of the equilibrium equations and, hence, a lower overall
solution cost. Therefore, the unsymmetric matrix solution scheme is not invoked
automatically when jointed material behavior is defined.
Elements
The jointed material model can be used with plane strain, generalized plane strain,
axisymmetric, and three-dimensional solid (continuum) elements in Abaqus/Standard. This model cannot be used with elements for which the assumed stress state is plane
stress (plane stress, shell, and membrane elements).
Output
In addition to the standard output identifiers available in Abaqus/Standard (Abaqus/Standard Output Variable Identifiers), the following
variables have special meaning in the jointed material model:
PE
Sum of the plastic strains for all four possible systems.
PEEQ
Sum of the equivalent plastic strains for all four possible systems.
PEQC
Equivalent plastic strains for all four possible systems (three joints -
PEQC1,
PEQC2, and
PEQC3, and bulk material -
PEQC4). This identifier also
provides yes/no flags (1/0 on the output database) AC
YIELD1, AC YIELD2,
AC YIELD3, and AC
YIELD4 indicating if each individual system is currently yielding,
that is, whether or not the plastic strain changed during the increment.