Convergence Checks
By default, Abaqus/Standard uses a combination of factors to determine whether the solution during a given increment has converged or not. The convergence checking algorithms are based upon the following:
- comparing the largest residual for a given field to the corresponding time-averaged flux, and
- comparing the largest correction for a field to the largest increment for the same field.
In addition, when contact is present in the model, the converged solution also has to satisfy contact penetration and slip compatibilities and contact force errors must be less than their respective tolerances.
The default convergence checks tend to work quite well in most applications, especially in the structural mechanics domain. However, in problems involving strong coupling between two or more physical fields (that is, multiphysics applications), the default criteria can be somewhat strict and conservative, possibly leading to a large number of iterations, cutbacks, and increments. For such problems, Abaqus/Standard also offers a set of alternative and relaxed convergence measures. Within a given step, these alternative convergence measures can be used globally such that a specified convergence measure is applied to all the active fields in the model or they can be applied on an individual field basis. In the latter case, Abaqus/Standard continues to use the default convergence criteria for all the other fields. Within such a framework, Abaqus/Standard also provides the additional flexibility of changing the convergence criteria for the various active fields from one step to another.
Strict (Default) Convergence Measure
Abaqus/Standard provides default convergence measures applicable for all fields in a multiphysics simulation. However, you can optionally choose to apply the strict criteria to one or more specific fields only and to augment this strict criteria with alternative (and potentially different) criteria for each of the other fields. In addition to the default contact convergence checks, the strict convergence measure requires the following conditions to be satisfied before Abaqus/Standard accepts the incremental solution as converged:
- Ratio of the largest residual flux to the time averaged flux is less than a tolerance, and
- Ratio of the largest correction to the largest increment is less than a tolerance.
Input File Usage
CONTROLS, PARAMETERS=FIELD, FIELD=field, CONVERGENCE CHECK=STRICT
Moderate Convergence Measure
The moderate convergence measure requires the following conditions to be satisfied for the specified field for Abaqus/Standard to accept the incremental solution as converged:
- Ratio of the largest residual to the largest flux is less than a tolerance, and
- Ratio of the largest correction to the largest increment is less than a tolerance.
In addition, if contact is active in the model, Abaqus/Standard enforces the following modified contact convergence checks to accept convergence of iterations:
- Ratio of the maximum contact force error to the largest flux is less than a tolerance, and
- Ratio of the maximum contact compatibility error to the largest increment is less than a modified tolerance which is obtained by scaling the default tolerance by 10.
Compared to the strict convergence criterion, the moderate convergence criterion uses a different metric for the residual convergence. It compares the largest residual to the largest flux (instead of to the time-averaged flux, as in the strict measure) anywhere in the domain. This criterion is useful for applications when it is important to model the region with the largest flux for a particular field accurately. Relatively smaller changes in flux in other regions of the model do not affect the convergence in this approach. This measure might be a useful alternative in models for which the time-average flux is small, making it difficult for the strict measure to be satisfied.
Input File Usage
CONTROLS, PARAMETERS=FIELD, FIELD=field, CONVERGENCE CHECK=MODERATE
Relaxed Convergence Measure
The relaxed convergence measure is based only upon the largest correction to the specified field. The residual tolerances do not play any role for this criterion. Therefore, the relaxed measure accepts an incremental solution as converged when only the following criterion is satisfied:
- The ratio of the largest correction to the largest increment is less than a tolerance.
In addition, if contact is active in the model, Abaqus/Standard enforces modified contact convergence checks to accept convergence of iterations. In this case, Abaqus ignores the contact force error check and enforces only the following contact compatibility check:
- Ratio of the maximum contact compatibility error to the largest increment is less than a modified tolerance, which is obtained by scaling the default tolerance by 10.
The relaxed convergence measure ignores the residual checks. For well-posed nonlinear incremental boundary value problems with a nonsingular “stiffness matrix” (left-hand side of the linear system of equations), it is reasonable to assume that in most cases a small correction is the result of a small residual (right-hand side of the linear system of equations). For such well-posed problems, a relaxed convergence measure might prove more effective, especially when the time-averaged residual for a particular field is quite “small,” and does not decrease with further iterations.
Input File Usage
CONTROLS, PARAMETERS=FIELD, FIELD=field, CONVERGENCE CHECK=RELAXED
Concept Design Convergence Measure
The concept design convergence measure treats an increment as converged if either the residual check or the correction check of the strict convergence measure is satisfied. In other words, the incremental solution is accepted if either one of the following conditions is satisfied:
- Ratio of the largest residual to the time-average flux is less than a tolerance, or
- Ratio of the largest correction to the largest increment is less than a tolerance.
In addition, if contact is active in the model, Abaqus/Standard enforces the following modified contact convergence checks to accept convergence of iterations:
- Ratio of the maximum contact force error to the time average flux is less than a tolerance, or
- Ratio of the maximum contact compatibility error to the largest increment is less than a modified tolerance, which is obtained by scaling the default tolerance by 10.
Input File Usage
CONTROLS, PARAMETERS=FIELD, FIELD=field, CONVERGENCE CHECK=CONCEPT DESIGN