*HEADING
 Structural analysis of printing a 42-layer thinwall (LDED, Inconel625) 
 Inter-layer dwell time 0s
** Units: <mm,N,tonne,s,Celsius>
**------------------------------------------------
*INCLUDE, INPUT=ABQ_am_special_purpose_types.inp
**------------------------------------------------
*INCLUDE, INPUT = mesh_thinwall_st.inp
*SOLID SECTION, MATERIAL=Inconel625, ELSET=PartToFabricate
*SOLID SECTION, MATERIAL=Inconel625, ELSET=Substrate
*SOLID SECTION, MATERIAL=Aluminum, 	 ELSET=Clamp
*ELEMENT PROGRESSIVE ACTIVATION, NAME="LDED.Printing", ELSET=PartToFabricate
**------------------------------------------------
*MATERIAL, NAME=Aluminum
*ELASTIC
** Unit: MPa, -
 70E3, 0.35
*EXPANSION
** Unit: /C
 23.1E-6
**
*MATERIAL, NAME=Inconel625
*ELASTIC
** Unit: MPa, -
 208e+03, 0.366,  20. 
 204e+03, 0.366,  93. 
 198e+03, 0.366, 205. 
 192e+03, 0.366, 315. 
 186e+03, 0.366, 425. 
 179e+03, 0.366, 540. 
 170e+03, 0.366, 650. 
 161e+03, 0.366, 760. 
 148e+03, 0.366, 870. 
*EXPANSION
** Unit: /C
 12.8e-06,   20.
 12.8e-06,   93.
 13.1e-06,  205.
 13.3e-06,  315.
 13.7e-06,  425.
 14.0e-06,  540.
 14.8e-06,  650.
 15.3e-06,  760.
 15.8e-06,  870.
*PLASTIC
** Unit: MPa, -
 493., 0.,20.
 479., 0.,93.
 443., 0.,205.
 430., 0.,315.
 424., 0.,425.
 423., 0.,540.
 422., 0.,650.
 415., 0.,760.
 386., 0.,870.
**------------------------------------------------
**Material Deposition
*PARAMETER
 beadWidth      = 3.35
 beadHeight     = 0.9071
**
*TABLE COLLECTION, NAME="ABQ_AM.MaterialDeposition"
*PARAMETER TABLE, TYPE= "ABQ_AM_MaterialDeposition"
 "LDED.PrintHeadDepositionTrajectory","Bead"
**
*PARAMETER TABLE,  TYPE= "ABQ_AM_MaterialDeposition_Bead"
 "Z", <beadHeight>, <beadWidth>, 0.,"Below"
**
*PARAMETER TABLE,  TYPE= "ABQ_AM_MaterialDeposition_Advanced"
 "Full",0.0,0.0,0.01,,,
**------------------------------------------------
*Event Series, Name="LDED.PrintHeadDepositionTrajectory",
               Type="ABQ_AM_MaterialDeposition",
               Time=Total, input=es_thinwall_dwell0.inp
**------------------------------------------------
*INITIAL CONDITIONS,TYPE=TEMPERATURE
 PartToFabricate, 1290.
 Substrate, 26.
 Clamp, 26.
*BOUNDARY
 ClampBottom, 1, 3
 ClampTop, 1, 3
**------------------------------------------------
*STEP,INC=80000, NAME=Printing, EXTRAPOLATION=NO
*STATIC
 0.5, 1794.24, 0.5e-10,0.5
*ACTIVATE ELEMENTS,ACTIVATION="LDED.Printing", EXPANSION TIME CONSTANT=0.5
 "ABQ_AM.MaterialDeposition"
*TEMPERATURE, FILE=am_lded_thinwall_inconel625_dwell0_ht.odb, BSTEP=1
*OUTPUT,FIELD,FREQ=200
*NODE OUTPUT
 U
*OUTPUT,FIELD,FREQ=200
*ELEMENT OUTPUT
 S, E, PEEQ
*OUTPUT, HISTORY,FREQ=1
*NODE OUTPUT, NSET=NOutputLDS
 U3
*END STEP
**------------------------------------------------
*STEP, INC=80000, NAME=Cooling, EXTRAPOLATION=NO
*STATIC
 10, 500, 10E-10, 10
*TEMPERATURE, FILE=am_lded_thinwall_inconel625_dwell0_ht.odb, BSTEP=2
*OUTPUT,FIELD,NUMBER INTERVAL=5
*NODE OUTPUT
 U
*OUTPUT,FIELD,NUMBER INTERVAL=5
*ELEMENT OUTPUT
 S, E, PEEQ
*OUTPUT, HISTORY,FREQ=1
*NODE OUTPUT, NSET=NOutputLDS
 U3
*END STEP
**------------------------------------------------
*STEP, INC=80000, NAME=MoreCooling, EXTRAPOLATION=NO
*STATIC
 100, 10000, 100E-10, 100
*TEMPERATURE, FILE=am_lded_thinwall_inconel625_dwell0_ht.odb, BSTEP=3
*CONTROLS, PARAMETERS=FIELD
 , 1.
*OUTPUT,FIELD,NUMBER INTERVAL=5
*NODE OUTPUT
 U
*OUTPUT,FIELD,NUMBER INTERVAL=5
*ELEMENT OUTPUT
 S, E, PEEQ
*OUTPUT, HISTORY,FREQ=1
*NODE OUTPUT, NSET=NOutputLDS
 U3
*END STEP
**===================================================================